| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bfs: handle set_blocksize failures
bfs uses buffer_heads, which don't handle block size > PAGE_SIZE well.
Without this, mounting will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call. |
| In the Linux kernel, the following vulnerability has been resolved:
qnx4: handle set_blocksize failures
qnx4 uses buffer_heads, which don't handle block size > PAGE_SIZE well.
Without this, mounting will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: handle set_blocksize failures
jfs uses buffer_heads, which don't handle block size > PAGE_SIZE well.
Without this, mounting we will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call. |
| In the Linux kernel, the following vulnerability has been resolved:
hpfs: handle set_blocksize failures
hpfs uses buffer_heads, which don't handle block size > PAGE_SIZE well.
Without this, mounting will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call. |
| In the Linux kernel, the following vulnerability has been resolved:
omfs: handle set_blocksize failures
omfs uses buffer_heads, which don't handle block size > PAGE_SIZE well.
Without this, mounting we will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: add boundary checks in acpi_ps_get_next_field()
Add boundary checks in acpi_ps_get_next_field() to prevent out-of-bounds
access. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Fix integer overflow in acpi_ex_opcode_3A_1T_1R() (mid_op)
Add overflow check for Index + Length to prevent integer overflow
when calculating the truncation length. This prevents negative
size parameter being passed to memcpy(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/umem: Be careful about boundary conditions in ib_umem_find_best_pgsz()
Several corner cases, especially important on 32 bits:
- umem->iova is u64, the function argument should pass in u64 or
iova will be truncated
- Check that the length is not too large for the iova
- Check that lengths > 4G don't overflow the GENMASK |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fc: Do not cancel requests in io target before it is initialized
A new nvme-fc controller in CONNECTING state sees admin request timeout
schedules ctrl->ioerr_work to abort inflight requests. This ends up
calling __nvme_fc_abort_outstanding_ios() which aborts requests in both
admin and io tagsets. In case fc_ctrl->tag_set was not initialized we
see the warning below. This is because ctrl.queue_count is initialized
early in nvme_fc_alloc_ctrl().
nvme nvme0: NVME-FC{0}: starting error recovery Connectivity Loss
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
lpfc 0000:ab:00.0: queue 0 connect admin queue failed (-6).
you didn't initialize this object before use?
turning off the locking correctness validator.
Workqueue: nvme-reset-wq nvme_fc_ctrl_ioerr_work [nvme_fc]
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x80
register_lock_class+0x567/0x580
__lock_acquire+0x330/0xb90
lock_acquire.part.0+0xad/0x210
blk_mq_tagset_busy_iter+0xf9/0xc00
__nvme_fc_abort_outstanding_ios+0x23f/0x320 [nvme_fc]
nvme_fc_ctrl_ioerr_work+0x172/0x210 [nvme_fc]
process_one_work+0x82c/0x1450
worker_thread+0x5ee/0xfd0
kthread+0x3a0/0x750
ret_from_fork+0x439/0x670
ret_from_fork_asm+0x1a/0x30
</TASK>
Update the check in __nvme_fc_abort_outstanding_ios() confirm that io
tagset was created before iterating over busy requests. Also make sure
to cancel ctrl->ioerr_work before removing io tagset. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: validate idmap key payload length
The cifs.idmap key type stores its payload length in key->datalen, which
is limited to U16_MAX. Accepting a larger key payload truncates the
recorded length and can make later users interpret the payload using
inconsistent bounds.
Reject oversized preparsed payloads before allocating or copying them.
This keeps key->datalen consistent with the stored data for both inline
and separately allocated idmap payloads. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/core: avoid infinite kdamond_merge_regions() internal loop
Patch series "mm/damon: unurgent fixes for infinite loop, NULL de-ref and
races", v1.1.
Sashiko found a few issues in DAMON that could cause infinite loop, NULL
dereference and monitoring results degradation. The first two sounds
scary but the infinite loop happens only under unreasonable user setup.
The NULL dereference is only in a unit test. Monitoring results
degradation is trivial since it is only best-effort, and those happens
from only unlikely races. Still those are bugs that better to fix if
possible. Fix those.
This patch (of 6):
Due to online parameter update like events, the number of DAMON regions
could be higher than the user-set upper limit. kdamond_merge_regions()
repeats merge regions until the number meets the limit, while doubling the
merge threshold up to the theoretical maximum threshold. It is tried only
up to the theoretical maximum threshold because even the aggressive
merging can fail from reducing the number of regions under the
user-defined upper limit. For example, there could be many user-defined
non-contiguous regions that cannot be merged.
The threshold based loop break condition is evaluated by comparing the
threshold for the next merging try against the theoretical maximum
threshold. If max_thres is larger than UINT_MAX / 2, doubling the
threshold could make it overflow, and bypass the loop break condition. In
the case, if the number of regions cannot be reduced under the upper limit
like explained above, the loop will run infinitely.
Prevent the case by doing the break condition check before doubling the
threshold. Also, prevent the threshold exceeding the maximum threshold,
as it could overflow and apply the wrong merge threshold.
This issue is unlikely to occur in real world, since having the max_thres
higher than UINT_MAX / 2 require unrealistically large aggregation
intervals compared to the sampling interval. Also, it requires an
unrealistically large number of uncontiguous regions setup. Nonetheless,
the consequence is bad and the fix is simple.
The issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: bail out of setup if the controller is inaccessible
xhci_gen_setup() locates the operational registers using the capability
length read from the very first register:
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
If the controller is dead or has dropped off the bus, that read returns
~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes
past the page-aligned MMIO base, i.e. unaligned. The first access
through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is
then an unaligned readl() on device memory. arm64 faults on unaligned
device accesses, so instead of xhci_handshake() catching the all-ones
value and returning -ENODEV, setup oopses:
xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci-pci-renesas 0005:08:00.0: xHCI Host Controller
xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1
Unable to handle kernel paging request at virtual address ffff80030a770103
ESR = 0x0000000096000021
FSC = 0x21: alignment fault
Internal error: Oops: 0000000096000021 [#1] SMP
pc : xhci_halt [xhci_hcd]
Call trace:
xhci_halt
xhci_gen_setup
xhci_pci_setup
usb_add_hcd
usb_hcd_pci_probe
xhci_pci_common_probe
xhci_pci_renesas_probe
This was hit with a Renesas uPD720201 that failed to power up ("Unable
to change power state from D3cold to D0, device inaccessible") yet still
reached the HCD probe path.
Read the capability register once, and if it reads back the all-ones
value (as xhci_handshake() and xhci_reset() already test for), abort
setup with -ENODEV before op_regs is derived from it. Reading it once
also avoids re-reading a register that may change under a concurrent
hot-removal. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix integer overflow in tipc_recvmsg() and tipc_recvstream()
In tipc_recvmsg(), the copy length is computed as:
copy = min_t(int, dlen - offset, buflen);
buflen is size_t but min_t(int, ...) casts it to int. When buflen
exceeds INT_MAX (e.g. 0xFFFFFFFF via io_uring provided buffers), it
wraps negative, wins the comparison, and the negative copy length
propagates to simple_copy_to_iter() where int-to-size_t promotion
makes it SIZE_MAX, triggering a WARN_ON. tipc_recvstream() has the
same pattern.
Kernel panic - not syncing: kernel: panic_on_warn set ...
RIP: 0010:simple_copy_to_iter+0x9e/0xd0 (net/core/datagram.c:521)
Call Trace:
__skb_datagram_iter+0x123/0x8b0 (net/core/datagram.c:402)
skb_copy_datagram_iter+0x77/0x1a0 (net/core/datagram.c:534)
tipc_recvmsg+0x3d7/0xe80 (net/tipc/socket.c:1934)
io_recvmsg+0x47e/0xda0
Fix by changing min_t(int, ...) to min_t(size_t, ...) in both
functions. The result is always <= (dlen - offset), which is bounded
by TIPC maximum message size (0x1ffff bytes), so the implicit
narrowing on assignment to int copy is always safe. |
| Uncontrolled Recursion vulnerability in Apache Thrift go bindings.
Both Go transports satisfy a read out of a buffered frame and, when that frame yields no payload bytes, read the next frame and call `Read` again instead of looping. A peer produces such a frame for 4 bytes in `TFramedTransport` (a declared size of zero) or 18 bytes in `THeaderTransport` (a header block that fills the frame), so nothing bounds the depth. The Go stack limit is reached as a `fatal error`, which `recover()` cannot catch, so the whole process dies.
This issue affects Apache Thrift: before 0.25.0.
Users are recommended to upgrade to version 0.25.0, which fixes the issue. |
| YesWiki before 4.6.7 contains an authorization bypass vulnerability in the comments API editComment route that allows authenticated low-privilege users to overwrite arbitrary pages or comments by supplying their own page as the pagetag field. Attackers can send a POST request to the api/comments endpoint targeting a victim tag, bypassing per-page write ACLs to replace content and reparent existing pages or comments. |
| A file-upload handler redirects the authenticated client's browser to a URL taken directly from that same request's Referer header, without validating it against the application's own origin. This allows an authenticated attacker to craft a request that causes another user's browser to be redirected to an arbitrary external destination after completing an upload. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mei: pass correct argument to function
The first argument to iwl_mei_write_cyclic_buf() should be the cldev
but the q_head pointer is passed instead. Fix it. |
| An authorization bypass vulnerability was identified in GitHub Enterprise Server that allowed any authenticated user of the instance to read the raw diff or patch of pull requests in private repositories without authorization. Access tokens for raw pull request diffs and patches were scoped to the repository name and pull request number rather than to a globally unique repository identifier, so an attacker who created a repository and pull request matching a target's repository name and pull request number could use a token for their own repository to retrieve the private pull request's contents. Exploitation required the attacker to know the target repository's name and a valid pull request number. This vulnerability affected all versions of GitHub Enterprise Server prior to 3.22 and was fixed in versions 3.17.21, 3.18.15, 3.19.12, 3.20.8, and 3.21.6. This vulnerability was reported via the GitHub Bug Bounty program. |
| A (D)TLS 1.2 client can accept a ChangeCipherSpec message before it has sent its ClientKeyExchange. No master secret has been derived at that point, so the client installs read keys derived from a known (deterministic) key and checks the server's Finished against that same key. An out-of-order ChangeCipherSpec can therefore be used by an attacker to complete the handshake in place of the server and send data the client accepts as authentic. The client's own traffic still uses correctly derived keys, so the attacker cannot read it, and the genuine server never completes the handshake. DTLS 1.2 clients are exposed because a datagram read can deliver the out-of-order records on its own. TLS 1.2 clients are exposed when the application supplies received bytes with wolfSSL_inject() or enables read ahead. For certificate suites, the attacker must be in a man-in-the-middle position. For PSK (Pre Shared Key) connections, any fake server can succeed without knowing the PSK. |
| Improper handling of highly compressed data (data amplification), Function call with incorrectly specified arguments, Improper validation of specified quantity in input vulnerability in Apache Thrift py bindings.
This issue affects Apache Thrift: before 0.25.0.
Users are recommended to upgrade to version 0.25.0, which fixes the issue. |
