| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: complete object teardown when the destroy command fails
erdma_destroy_qp(), erdma_destroy_cq(), erdma_dereg_mr(), and
erdma_destroy_ah() returned early when erdma_post_cmd_wait() failed,
leaking the queue buffers, MTTs, doorbells and the STAG, QPN, CQN and AHN
identifiers. A command timeout clears ERDMA_CMDQ_STATE_OK_BIT and
permanently disables the command queue, so no retry can succeed; the RDMA
core keeps the object after a failed destructor and forced uverbs cleanup
then nulls the pointers, making the resources unreachable.
Warn on failure but release every software-owned resource and return
success, since during terminal destruction the hardware command result is
only diagnostic. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix WARNING in bpf_tracing_link_release
The trampoline could be corrupted by the blindly
'tr->flags = BPF_TRAMP_F_TAIL_CALL_CTX' in verifier.
1. A fexit attached to a tail_call_reachable prog. 'tr->flags' became
'BPF_TRAMP_F_CALL_ORIG | BPF_TRAMP_F_TAIL_CALL_CTX'. And, the
trampoline would poke the target prog's nop insn using jmp insn instead
of call insn.
2. Another fexit loaded with the same tail_call_reachable prog target.
'tr->flags' became 'BPF_TRAMP_F_TAIL_CALL_CTX'.
3. Close the first fexit link. Due to no BPF_TRAMP_F_CALL_ORIG in
'tr->flags', the trampoline will fail to restore the prog's nop insn
using call insn.
[ 3.410719] WARNING: kernel/bpf/syscall.c:3551 at bpf_tracing_link_release+0x53/0x60, CPU#1: test_progs/98
...
[ 3.428793] bpf_link_free+0x58/0x130
[ 3.429293] bpf_link_release+0x23/0x30
Fix the warning by updating 'tr->flags' with '|=' and lock. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: use devm_gpiochip_add_data() for GPIO chip
The gpio_chip is allocated with device-managed memory but registered with
the non-managed gpiochip_add_data(). This was harmless while the drivers
were built-in, but once they can be built as modules and unbound/rmmod'd,
devm frees the gpio_chip's memory while it is still registered, causing a
use-after-free.
Register it with devm_gpiochip_add_data() so it shares the same
device-managed lifecycle, which also lets the manual gpiochip_remove()
error paths go away. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Validate string descriptors
The string descriptor length includes a two-byte header while the UTF-16
payload starts after it. utf16s_to_utf8s() expects a count of UTF-16 code
units, not bytes. Passing the payload byte count can make it read beyond
the descriptor buffer.
Validate that the payload has an even byte count, pass a code-unit count to
the converter, and allocate sufficient UTF-8 output space.
The raw string buffer starts after the descriptor header but its size is
bLength. Copying bLength bytes from that pointer can read beyond the
response buffer.
Allocate a zeroed bLength-sized buffer and copy only the UTF-16
payload. This preserves the raw buffer size consumed by the RPMB device-ID
ABI while avoiding the overread. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: oc-tiny: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_irq(). During removal,
spi_bitbang_stop() only unregisters the controller; the subsequent
spi_controller_put() then frees the controller together with its
embedded driver-private devdata, which is the IRQ handler's dev_id. The
devm_request_irq() release action (free_irq()), which drains the
handler, does not run until after .remove() returns. A late or latched
interrupt can therefore reach tiny_spi_irq() and dereference
already-freed memory (e.g. hw->base).
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix UAF when probe runs concurrent to dyn ID removal
Dynamic IDs are only guaranteed to be valid when dynids.lock is held,
as remove_id_store() can free the node. Thus, make a copy in
pci_match_device(). Also, clarify that the id parameter is only valid
during probe. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix BUG in nilfs_copy_dirty_pages() on dirty state mismatch
Syzbot reported a kernel BUG triggered within nilfs_copy_dirty_pages(),
which copies dirty DAT file folios/pages to its shadow page cache. The
BUG occurs when a retrieved dirty folio/page unexpectedly loses its
'dirty' status.
This issue arises because, since the commit referenced below, the 'dirty'
flag of a folio/page can be cleared asynchronously after the filesystem
detects metadata corruption and transitions to read-only mode.
Resolve the issue by returning an -EROFS error if the filesystem has
transitioned to read-only mode. Also change the behavior to issue a
kernel warning only once instead of triggering a kernel BUG when this
unexpected 'dirty' state is detected while the filesystem is not in
read-only mode. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/cxgb4: Fix dereg_skb leak and double free in write_tpt_entry()
When the device is in the fatal error state, write_tpt_entry() returns -EIO
before handing the caller's preallocated skb to the transmit path; its
allocation-failure returns do the same. c4iw_dereg_mr() ignores the error
and frees mhp, leaking mhp->dereg_skb. c4iw_get_dma_mr() instead frees the
skb a second time after dereg_mem() already consumed it, a double free.
Make write_tpt_entry() the sole owner of a non-NULL skb, freeing it on
every return preceding handoff to c4iw_ofld_send(): fatal error, tpt and
stag allocation failure. c4iw_ofld_send() consumes the skb on success and
error alike, so drop the redundant kfree_skb() in c4iw_get_dma_mr() after
dereg_mem(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: davinci: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_threaded_irq(). During
removal, spi_bitbang_stop() only unregisters the controller; the
subsequent spi_controller_put() then frees the controller together with
its embedded davinci_spi devdata, which is the IRQ handler's dev_id.
The devm_request_threaded_irq() release action (free_irq()), which
drains the handler, does not run until after .remove() returns. A late
or latched interrupt can therefore reach davinci_spi_irq() and
dereference already-freed memory.
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
The clock is acquired with devm_clk_get_enabled(), which is registered
after the IRQ and thus released before it by the devres LIFO order.
Drain the interrupt explicitly with devm_free_irq() before disabling the
controller so that a late interrupt cannot access the registers of a
clock-gated controller.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix overreads in ath11k_wmi_process_csa_switch_count_event()
There is no policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT, so
the parse infrastructure does not enforce a minimum length for the event
struct. Additionally, the num_vdevs field is taken directly from firmware
and used as a loop bound over the vdev_ids array without checking that it
fits within the TLV payload. Either condition can cause an out-of-bounds
read.
Add a TLV policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT so
the parse infrastructure enforces a minimum length for the fixed-size event
struct. Add a helper ath11k_wmi_tlv_data_len() to recover the payload
length of a parsed TLV from the header preceding its data pointer. Use it
in ath11k_wmi_process_csa_switch_count_event() to bound num_vdevs before
the loop.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix stride mismatch in mac_phy_caps_parse()
Currently, in ath11k_wmi_tlv_mac_phy_caps_parse(), kcalloc() sizes the
mac_phy_caps buffer as tot_phy_id * len, where len is clamped to
min(firmware_len, sizeof(struct wmi_mac_phy_capabilities)). The subsequent
memcpy() destination advances by sizeof(full struct) per slot via C
pointer arithmetic, not by the clamped len. When firmware sends short
TLVs, the second and later slots are written past the end of the
allocation.
The reader in ath11k_pull_mac_phy_cap_svc_ready_ext() also indexes the
buffer with full-struct pointer arithmetic, so the allocation must match
that stride.
Fix by using kzalloc_objs(), which derives the element size from the
pointer type, making allocation size and pointer stride provably
consistent regardless of what len the firmware provides.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix potential UAF when reading bpf link info
In bpf_link_show_fdinfo and bpf_link_get_info_by_fd, link->prog is
accessed without holding any locks. If the prog is concurrently replaced
via bpf_link_update, the old prog can be freed, leading to a potential
UAF issue.
Fix this by accessing link->prog under RCU protection to safely fetch
the pointer and guarantee its lifetime while reading its fields. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: create serial pool adding rdev to array with serialize_policy=1
The following bug has been observed with kernel 7.1.3 after adding a new
rdev to an existing RAID1 array with serialize_policy enabled:
Oops: 0002 [#1]
CPU: 0 UID: 0 PID: 19639 Comm: ext4lazyinit Not tainted 7.1.3-1-default
RIP: _raw_spin_lock_irqsave+0x27/0x50
CR2: 0000000000004960
Call Trace:
wait_for_serialization+0xb9/0x260 [raid1]
raid1_make_request+0x762/0xaff [raid1]
md_handle_request+0x1c9/0x2e0 [md_mod]
The raid1.c code calls wait_for_serialization() if the MD_SERIALIZE_POLICY
is set, and wait_for_serialization assumes that rdev->serial is
initialized. Normally this will be the case for arrays that have
the serialize_policy sysfs attribute set to 1.
But when a new rdev is added to an existing array in bind_rdev_to_array(),
the condition at mddev_create_serial_pool() causes creation of rdev->serial
to be skipped. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: sgi-gru: remove interrupt-context page-table walks
The GRU TLB miss handler walks a process's page tables without holding
page-table locks or a reference to the mapped page. It also uses a kernel
page-table accessor on user page tables and supports only PMD-level large
mappings on x86-64.
Remove the direct walker. Send interrupt faults directly to user polling
mode so the existing call-OS fallback retries them in process context.
Remove the mmap-lock failure statistic that can no longer be incremented. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix non-AQL packet accounting for MLO stations
__mt76_tx_queue_skb() overrides the wcid passed by the driver with
sta->drv_priv, so the wcid might incorrectly be changed after TX,
causing wcid->non_aql_packets to be counted on the wrong wcid. For
example, on the AP side, if a station's setup link is the 5G link and
the station uses 2G to transmit a frame, the value of non_aql_packets
is increased on the 5G wcid but decreased on the 2G wcid. Once the
inflated counter exceeds MT_MAX_NON_AQL_PKT, the TX scheduler
permanently refuses to service the station.
Drop the reassignment and account on the wcid used for transmission.
This also records the actual wcid in the queue entry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unwind state on add_interface failure
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: cancel reset and rc work on device unregister
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, x86: Fix trampoline stack size for 128-bit arguments
btf_distill_func_proto() accepts a function argument up to 16 bytes, so a
128-bit scalar such as __int128 reaches the x86 trampoline with
arg_size == 16. But the current implementation assumes an __int128
argument only needs one register, so the register save area is
under-allocated and save_args() overwrites adjacent stack slots.
Compute the register count from arg_size for all arguments to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data. |
