| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in __ksmbd_close_fd() via durable scavenger
When a durable file handle survives session disconnect (TCP close without
SMB2_LOGOFF), session_fd_check() sets fp->conn = NULL to preserve the
handle for later reconnection. However, it did not clean up the byte-range
locks on fp->lock_list.
Later, when the durable scavenger thread times out and calls
__ksmbd_close_fd(NULL, fp), the lock cleanup loop did:
spin_lock(&fp->conn->llist_lock);
This caused a slab use-after-free because fp->conn was NULL and the
original connection object had already been freed by
ksmbd_tcp_disconnect().
The root cause is asymmetric cleanup: lock entries (smb_lock->clist) were
left dangling on the freed conn->lock_list while fp->conn was nulled out.
To fix this issue properly, we need to handle the lifetime of
smb_lock->clist across three paths:
- Safely skip clist deletion when list is empty and fp->conn is NULL.
- Remove the lock from the old connection's lock_list in
session_fd_check()
- Re-add the lock to the new connection's lock_list in
ksmbd_reopen_durable_fd(). |
| In the Linux kernel, the following vulnerability has been resolved:
lib/crypto: chacha: Zeroize permuted_state before it leaves scope
Since the ChaCha permutation is invertible, the local variable
'permuted_state' is sufficient to compute the original 'state', and thus
the key, even after the permutation has been done.
While the kernel is quite inconsistent about zeroizing secrets on the
stack (and some prominent userspace crypto libraries don't bother at all
since it's not guaranteed to work anyway), the kernel does try to do it
as a best practice, especially in cases involving the RNG.
Thus, explicitly zeroize 'permuted_state' before it goes out of scope. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix SCX_KICK_WAIT deadlock by deferring wait to balance callback
SCX_KICK_WAIT busy-waits in kick_cpus_irq_workfn() using
smp_cond_load_acquire() until the target CPU's kick_sync advances. Because
the irq_work runs in hardirq context, the waiting CPU cannot reschedule and
its own kick_sync never advances. If multiple CPUs form a wait cycle, all
CPUs deadlock.
Replace the busy-wait in kick_cpus_irq_workfn() with resched_curr() to
force the CPU through do_pick_task_scx(), which queues a balance callback
to perform the wait. The balance callback drops the rq lock and enables
IRQs following the sched_core_balance() pattern, so the CPU can process
IPIs while waiting. The local CPU's kick_sync is advanced on entry to
do_pick_task_scx() and continuously during the wait, ensuring any CPU that
starts waiting for us sees the advancement and cannot form cyclic
dependencies. |
| In the Linux kernel, the following vulnerability has been resolved:
media: solo6x10: Check for out of bounds chip_id
Clang with CONFIG_UBSAN_SHIFT=y noticed a condition where a signed type
(literal "1" is an "int") could end up being shifted beyond 32 bits,
so instrumentation was added (and due to the double is_tw286x() call
seen via inlining), Clang decides the second one must now be undefined
behavior and elides the rest of the function[1]. This is a known problem
with Clang (that is still being worked on), but we can avoid the entire
problem by actually checking the existing max chip ID, and now there is
no runtime instrumentation added at all since everything is known to be
within bounds.
Additionally use an unsigned value for the shift to remove the
instrumentation even without the explicit bounds checking.
[hverkuil: fix checkpatch warning for is_tw286x] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: dummy-hcd: Fix locking/synchronization error
Syzbot testing was able to provoke an addressing exception and crash
in the usb_gadget_udc_reset() routine in
drivers/usb/gadgets/udc/core.c, resulting from the fact that the
routine was called with a second ("driver") argument of NULL. The bad
caller was set_link_state() in dummy_hcd.c, and the problem arose
because of a race between a USB reset and driver unbind.
These sorts of races were not supposed to be possible; commit
7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous synchronization change"),
along with a few followup commits, was written specifically to prevent
them. As it turns out, there are (at least) two errors remaining in
the code. Another patch will address the second error; this one is
concerned with the first.
The error responsible for the syzbot crash occurred because the
stop_activity() routine will sometimes drop and then re-acquire the
dum->lock spinlock. A call to stop_activity() occurs in
set_link_state() when handling an emulated USB reset, after the test
of dum->ints_enabled and before the increment of dum->callback_usage.
This allowed another thread (doing a driver unbind) to sneak in and
grab the spinlock, and then clear dum->ints_enabled and dum->driver.
Normally this other thread would have to wait for dum->callback_usage
to go down to 0 before it would clear dum->driver, but in this case it
didn't have to wait since dum->callback_usage had not yet been
incremented.
The fix is to increment dum->callback_usage _before_ calling
stop_activity() instead of after. Then the thread doing the unbind
will not clear dum->driver until after the call to
usb_gadget_udc_reset() safely returns and dum->callback_usage has been
decremented again. |
| In the Linux kernel, the following vulnerability has been resolved:
interconnect: qcom: sm8450: Fix NULL pointer dereference in icc_link_nodes()
The change to dynamic IDs for SM8450 platform interconnects left two links
unconverted, fix it to avoid the NULL pointer dereference in runtime,
when a pointer to a destination interconnect is not valid:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
<...>
Call trace:
icc_link_nodes+0x3c/0x100 (P)
qcom_icc_rpmh_probe+0x1b4/0x528
platform_probe+0x64/0xc0
really_probe+0xc4/0x2a8
__driver_probe_device+0x80/0x140
driver_probe_device+0x48/0x170
__device_attach_driver+0xc0/0x148
bus_for_each_drv+0x88/0xf0
__device_attach+0xb0/0x1c0
device_initial_probe+0x58/0x68
bus_probe_device+0x40/0xb8
deferred_probe_work_func+0x90/0xd0
process_one_work+0x15c/0x3c0
worker_thread+0x2e8/0x400
kthread+0x150/0x208
ret_from_fork+0x10/0x20
Code: 900310f4 911d6294 91008280 94176078 (f94002a0)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Oops: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: crypto: Use the correct destructor kfunc type
With CONFIG_CFI enabled, the kernel strictly enforces that indirect
function calls use a function pointer type that matches the target
function. I ran into the following type mismatch when running BPF
self-tests:
CFI failure at bpf_obj_free_fields+0x190/0x238 (target:
bpf_crypto_ctx_release+0x0/0x94; expected type: 0xa488ebfc)
Internal error: Oops - CFI: 00000000f2008228 [#1] SMP
...
As bpf_crypto_ctx_release() is also used in BPF programs and using
a void pointer as the argument would make the verifier unhappy, add
a simple stub function with the correct type and register it as the
destructor kfunc instead. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: adxl380: Avoid reading more entries than present in FIFO
The interrupt handler reads FIFO entries in batches of N samples, where N
is the number of scan elements that have been enabled. However, the sensor
fills the FIFO one sample at a time, even when more than one channel is
enabled. Therefore,the number of entries reported by the FIFO status
registers may not be a multiple of N; if this number is not a multiple, the
number of entries read from the FIFO may exceed the number of entries
actually present.
To fix the above issue, round down the number of FIFO entries read from the
status registers so that it is always a multiple of N. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: Reinit dev->spinlock between attachments to low-level drivers
`struct comedi_device` is the main controlling structure for a COMEDI
device created by the COMEDI subsystem. It contains a member `spinlock`
containing a spin-lock that is initialized by the COMEDI subsystem, but
is reserved for use by a low-level driver attached to the COMEDI device
(at least since commit 25436dc9d84f ("Staging: comedi: remove RT
code")).
Some COMEDI devices (those created on initialization of the COMEDI
subsystem when the "comedi.comedi_num_legacy_minors" parameter is
non-zero) can be attached to different low-level drivers over their
lifetime using the `COMEDI_DEVCONFIG` ioctl command. This can result in
inconsistent lock states being reported when there is a mismatch in the
spin-lock locking levels used by each low-level driver to which the
COMEDI device has been attached. Fix it by reinitializing
`dev->spinlock` before calling the low-level driver's `attach` function
pointer if `CONFIG_LOCKDEP` is enabled. |
| In the Linux kernel, the following vulnerability has been resolved:
mshv_vtl: Fix vmemmap_shift exceeding MAX_FOLIO_ORDER
When registering VTL0 memory via MSHV_ADD_VTL0_MEMORY, the kernel
computes pgmap->vmemmap_shift as the number of trailing zeros in the
OR of start_pfn and last_pfn, intending to use the largest compound
page order both endpoints are aligned to.
However, this value is not clamped to MAX_FOLIO_ORDER, so a
sufficiently aligned range (e.g. physical range
[0x800000000000, 0x800080000000), corresponding to start_pfn=0x800000000
with 35 trailing zeros) can produce a shift larger than what
memremap_pages() accepts, triggering a WARN and returning -EINVAL:
WARNING: ... memremap_pages+0x512/0x650
requested folio size unsupported
The MAX_FOLIO_ORDER check was added by
commit 646b67d57589 ("mm/memremap: reject unreasonable folio/compound
page sizes in memremap_pages()").
Fix this by clamping vmemmap_shift to MAX_FOLIO_ORDER so we always
request the largest order the kernel supports, in those cases, rather
than an out-of-range value.
Also fix the error path to propagate the actual error code from
devm_memremap_pages() instead of hard-coding -EFAULT, which was
masking the real -EINVAL return. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: dts: qcom: monaco: Reserve full Gunyah metadata region
We observe spurious "Synchronous External Abort" exceptions
(ESR=0x96000010) and kernel crashes on Monaco-based platforms.
These faults are caused by the kernel inadvertently accessing
hypervisor-owned memory that is not properly marked as reserved.
>From boot log, The Qualcomm hypervisor reports the memory range
at 0x91a80000 of size 0x80000 (512 KiB) as hypervisor-owned:
qhee_hyp_assign_remove_memory: 0x91a80000/0x80000 -> ret 0
However, the EFI memory map provided by firmware only reserves the
subrange 0x91a40000–0x91a87fff (288 KiB). The remaining portion
(0x91a88000–0x91afffff) is incorrectly reported as conventional
memory (from efi debug):
efi: 0x000091a40000-0x000091a87fff [Reserved...]
efi: 0x000091a88000-0x0000938fffff [Conventional...]
As a result, the allocator may hand out PFNs inside the hypervisor
owned region, causing fatal aborts when the kernel accesses those
addresses.
Add a reserved-memory carveout for the Gunyah hypervisor metadata
at 0x91a80000 (512 KiB) and mark it as no-map so Linux does not
map or allocate from this area.
For the record:
Hyp version: gunyah-e78adb36e debug (2025-11-17 05:38:05 UTC)
UEFI Ver: 6.0.260122.BOOT.MXF.1.0.c1-00449-KODIAKLA-1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipa: fix event ring index not programmed for IPA v5.0+
For IPA v5.0+, the event ring index field moved from CH_C_CNTXT_0 to
CH_C_CNTXT_1. The v5.0 register definition intended to define this
field in the CH_C_CNTXT_1 fmask array but used the old identifier of
ERINDEX instead of CH_ERINDEX.
Without a valid event ring, GSI channels could never signal transfer
completions. This caused gsi_channel_trans_quiesce() to block
forever in wait_for_completion().
At least for IPA v5.2 this resolves an issue seen where runtime
suspend, system suspend, and remoteproc stop all hanged forever. It
also meant the IPA data path was completely non functional. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid uninit-value access in f2fs_sanity_check_node_footer
syzbot reported a f2fs bug as below:
BUG: KMSAN: uninit-value in f2fs_sanity_check_node_footer+0x374/0xa20 fs/f2fs/node.c:1520
f2fs_sanity_check_node_footer+0x374/0xa20 fs/f2fs/node.c:1520
f2fs_finish_read_bio+0xe1e/0x1d60 fs/f2fs/data.c:177
f2fs_read_end_io+0x6ab/0x2220 fs/f2fs/data.c:-1
bio_endio+0x1006/0x1160 block/bio.c:1792
submit_bio_noacct+0x533/0x2960 block/blk-core.c:891
submit_bio+0x57a/0x620 block/blk-core.c:926
blk_crypto_submit_bio include/linux/blk-crypto.h:203 [inline]
f2fs_submit_read_bio+0x12c/0x360 fs/f2fs/data.c:557
f2fs_submit_page_bio+0xee2/0x1450 fs/f2fs/data.c:775
read_node_folio+0x384/0x4b0 fs/f2fs/node.c:1481
__get_node_folio+0x5db/0x15d0 fs/f2fs/node.c:1576
f2fs_get_inode_folio+0x40/0x50 fs/f2fs/node.c:1623
do_read_inode fs/f2fs/inode.c:425 [inline]
f2fs_iget+0x1209/0x9380 fs/f2fs/inode.c:596
f2fs_fill_super+0x8f5a/0xb2e0 fs/f2fs/super.c:5184
get_tree_bdev_flags+0x6e6/0x920 fs/super.c:1694
get_tree_bdev+0x38/0x50 fs/super.c:1717
f2fs_get_tree+0x35/0x40 fs/f2fs/super.c:5436
vfs_get_tree+0xb3/0x5d0 fs/super.c:1754
fc_mount fs/namespace.c:1193 [inline]
do_new_mount_fc fs/namespace.c:3763 [inline]
do_new_mount+0x885/0x1dd0 fs/namespace.c:3839
path_mount+0x7a2/0x20b0 fs/namespace.c:4159
do_mount fs/namespace.c:4172 [inline]
__do_sys_mount fs/namespace.c:4361 [inline]
__se_sys_mount+0x704/0x7f0 fs/namespace.c:4338
__x64_sys_mount+0xe4/0x150 fs/namespace.c:4338
x64_sys_call+0x39f0/0x3ea0 arch/x86/include/generated/asm/syscalls_64.h:166
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x134/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The root cause is: in f2fs_finish_read_bio(), we may access uninit data
in folio if we failed to read the data from device into folio, let's add
a check condition to avoid such issue. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: proximity: hx9023s: Protect against division by zero in set_samp_freq
Avoid division by zero when sampling frequency is unspecified. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix UAF in le_read_features_complete
This fixes the following backtrace caused by hci_conn being freed
before le_read_features_complete but after
hci_le_read_remote_features_sync so hci_conn_del -> hci_cmd_sync_dequeue
is not able to prevent it:
==================================================================
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
BUG: KASAN: slab-use-after-free in atomic_dec_and_test include/linux/atomic/atomic-instrumented.h:1383 [inline]
BUG: KASAN: slab-use-after-free in hci_conn_drop include/net/bluetooth/hci_core.h:1688 [inline]
BUG: KASAN: slab-use-after-free in le_read_features_complete+0x5b/0x340 net/bluetooth/hci_sync.c:7344
Write of size 4 at addr ffff8880796b0010 by task kworker/u9:0/52
CPU: 0 UID: 0 PID: 52 Comm: kworker/u9:0 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcd/0x630 mm/kasan/report.c:482
kasan_report+0xe0/0x110 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:194 [inline]
kasan_check_range+0x100/0x1b0 mm/kasan/generic.c:200
instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
atomic_dec_and_test include/linux/atomic/atomic-instrumented.h:1383 [inline]
hci_conn_drop include/net/bluetooth/hci_core.h:1688 [inline]
le_read_features_complete+0x5b/0x340 net/bluetooth/hci_sync.c:7344
hci_cmd_sync_work+0x1ff/0x430 net/bluetooth/hci_sync.c:334
process_one_work+0x9ba/0x1b20 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3421
kthread+0x3c5/0x780 kernel/kthread.c:463
ret_from_fork+0x983/0xb10 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
Allocated by task 5932:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:56
kasan_save_track+0x14/0x30 mm/kasan/common.c:77
poison_kmalloc_redzone mm/kasan/common.c:400 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:417
kmalloc_noprof include/linux/slab.h:957 [inline]
kzalloc_noprof include/linux/slab.h:1094 [inline]
__hci_conn_add+0xf8/0x1c70 net/bluetooth/hci_conn.c:963
hci_conn_add_unset+0x76/0x100 net/bluetooth/hci_conn.c:1084
le_conn_complete_evt+0x639/0x1f20 net/bluetooth/hci_event.c:5714
hci_le_enh_conn_complete_evt+0x23d/0x380 net/bluetooth/hci_event.c:5861
hci_le_meta_evt+0x357/0x5e0 net/bluetooth/hci_event.c:7408
hci_event_func net/bluetooth/hci_event.c:7716 [inline]
hci_event_packet+0x685/0x11c0 net/bluetooth/hci_event.c:7773
hci_rx_work+0x2c9/0xeb0 net/bluetooth/hci_core.c:4076
process_one_work+0x9ba/0x1b20 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3421
kthread+0x3c5/0x780 kernel/kthread.c:463
ret_from_fork+0x983/0xb10 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
Freed by task 5932:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:56
kasan_save_track+0x14/0x30 mm/kasan/common.c:77
__kasan_save_free_info+0x3b/0x60 mm/kasan/generic.c:587
kasan_save_free_info mm/kasan/kasan.h:406 [inline]
poison_slab_object mm/kasan/common.c:252 [inline]
__kasan_slab_free+0x5f/0x80 mm/kasan/common.c:284
kasan_slab_free include/linux/kasan.h:234 [inline]
slab_free_hook mm/slub.c:2540 [inline]
slab_free mm/slub.c:6663 [inline]
kfree+0x2f8/0x6e0 mm/slub.c:6871
device_release+0xa4/0x240 drivers/base/core.c:2565
kobject_cleanup lib/kobject.c:689 [inline]
kobject_release lib/kobject.c:720 [inline]
kref_put include/linux/kref.h:65 [inline]
kobject_put+0x1e7/0x590 lib/kobject.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
USB: dummy-hcd: Fix interrupt synchronization error
This fixes an error in synchronization in the dummy-hcd driver. The
error has a somewhat involved history. The synchronization mechanism
was introduced by commit 7dbd8f4cabd9 ("USB: dummy-hcd: Fix erroneous
synchronization change"), which added an emulated "interrupts enabled"
flag together with code emulating synchronize_irq() (it waits until
all current handler callbacks have returned).
But the emulated interrupt-disable occurred too late, after the driver
containing the handler callback routines had been told that it was
unbound and no more callbacks would occur. Commit 4a5d797a9f9c ("usb:
gadget: dummy_hcd: fix gpf in gadget_setup") tried to fix this by
moving the synchronize_irq() emulation code from dummy_stop() to
dummy_pullup(), which runs before the unbind callback.
There still were races, though, because the emulated interrupt-disable
still occurred too late. It couldn't be moved to dummy_pullup(),
because that routine can be called for reasons other than an impending
unbind. Therefore commits 7dc0c55e9f30 ("USB: UDC core: Add
udc_async_callbacks gadget op") and 04145a03db9d ("USB: UDC: Implement
udc_async_callbacks in dummy-hcd") added an API allowing the UDC core
to tell dummy-hcd exactly when emulated interrupts and their callbacks
should be disabled.
That brings us to the current state of things, which is still wrong
because the emulated synchronize_irq() occurs before the emulated
interrupt-disable! That's no good, beause it means that more emulated
interrupts can occur after the synchronize_irq() emulation has run,
leading to the possibility that a callback handler may be running when
the gadget driver is unbound.
To fix this, we have to move the synchronize_irq() emulation code yet
again, to the dummy_udc_async_callbacks() routine, which takes care of
enabling and disabling emulated interrupt requests. The
synchronization will now run immediately after emulated interrupts are
disabled, which is where it belongs. |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c: ov5647: Initialize subdev before controls
In ov5647_init_controls() we call v4l2_get_subdevdata, but it is
initialized by v4l2_i2c_subdev_init() in the probe, which currently
happens after init_controls(). This can result in a segfault if the
error condition is hit, and we try to access i2c_client, so fix the
order. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: restore failed global reservations to subpool
Commit a833a693a490 ("mm: hugetlb: fix incorrect fallback for subpool")
fixed an underflow error for hstate->resv_huge_pages caused by incorrectly
attributing globally requested pages to the subpool's reservation.
Unfortunately, this fix also introduced the opposite problem, which would
leave spool->used_hpages elevated if the globally requested pages could
not be acquired. This is because while a subpool's reserve pages only
accounts for what is requested and allocated from the subpool, its "used"
counter keeps track of what is consumed in total, both from the subpool
and globally. Thus, we need to adjust spool->used_hpages in the other
direction, and make sure that globally requested pages are uncharged from
the subpool's used counter.
Each failed allocation attempt increments the used_hpages counter by how
many pages were requested from the global pool. Ultimately, this renders
the subpool unusable, as used_hpages approaches the max limit.
The issue can be reproduced as follows:
1. Allocate 4 hugetlb pages
2. Create a hugetlb mount with max=4, min=2
3. Consume 2 pages globally
4. Request 3 pages from the subpool (2 from subpool + 1 from global)
4.1 hugepage_subpool_get_pages(spool, 3) succeeds.
used_hpages += 3
4.2 hugetlb_acct_memory(h, 1) fails: no global pages left
used_hpages -= 2
5. Subpool now has used_hpages = 1, despite not being able to
successfully allocate any hugepages. It believes it can now only
allocate 3 more hugepages, not 4.
With each failed allocation attempt incrementing the used counter, the
subpool eventually reaches a point where its used counter equals its
max counter. At that point, any future allocations that try to
allocate hugeTLB pages from the subpool will fail, despite the subpool
not having any of its hugeTLB pages consumed by any user.
Once this happens, there is no way to make the subpool usable again,
since there is no way to decrement the used counter as no process is
really consuming the hugeTLB pages.
The underflow issue that the original commit fixes still remains fixed
as well.
Without this fix, used_hpages would keep on leaking if
hugetlb_acct_memory() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: microchip: Fix error path in PTP IRQ setup
If request_threaded_irq() fails during the PTP message IRQ setup, the
newly created IRQ mapping is never disposed. Indeed, the
ksz_ptp_irq_setup()'s error path only frees the mappings that were
successfully set up.
Dispose the newly created mapping if the associated
request_threaded_irq() fails at setup. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: fix NULL pointer dereference in ublk_ctrl_set_size()
ublk_ctrl_set_size() unconditionally dereferences ub->ub_disk via
set_capacity_and_notify() without checking if it is NULL.
ub->ub_disk is NULL before UBLK_CMD_START_DEV completes (it is only
assigned in ublk_ctrl_start_dev()) and after UBLK_CMD_STOP_DEV runs
(ublk_detach_disk() sets it to NULL). Since the UBLK_CMD_UPDATE_SIZE
handler performs no state validation, a user can trigger a NULL pointer
dereference by sending UPDATE_SIZE to a device that has been added but
not yet started, or one that has been stopped.
Fix this by checking ub->ub_disk under ub->mutex before dereferencing
it, and returning -ENODEV if the disk is not available. |
