| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate inherited ACE SID length
smb_inherit_dacl() walks the parent directory DACL loaded from the
security descriptor xattr. It verifies that each ACE contains the fixed
SID header before using it, but does not verify that the variable-length
SID described by sid.num_subauth is fully contained in the ACE.
A malformed inheritable ACE can advertise more subauthorities than are
present in the ACE. compare_sids() may then read past the ACE.
smb_set_ace() also clamps the copied destination SID, but used the
unchecked source SID count to compute the inherited ACE size. That could
advance the temporary inherited ACE buffer pointer and nt_size accounting
past the allocated buffer.
Fix this by validating the parent ACE SID count and SID length before
using the SID during inheritance. Compute the inherited ACE size from the
copied SID so the size matches the bounded destination SID. Reject the
inherited DACL if size accumulation would overflow smb_acl.size or the
security descriptor allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix type confusion in bond_setup_by_slave()
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Completely fix fcport double free
In qla24xx_els_dcmd_iocb() sp->free is set to qla2x00_els_dcmd_sp_free().
When an error happens, this function is called by qla2x00_sp_release(),
when kref_put() releases the first and the last reference.
qla2x00_els_dcmd_sp_free() frees fcport by calling qla2x00_free_fcport().
Doing it one more time after kref_put() is a bad idea. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Fix race in DMA ring dequeue
The HCI DMA dequeue path (hci_dma_dequeue_xfer()) may be invoked for
multiple transfers that timeout around the same time. However, the
function is not serialized and can race with itself.
When a timeout occurs, hci_dma_dequeue_xfer() stops the ring, processes
incomplete transfers, and then restarts the ring. If another timeout
triggers a parallel call into the same function, the two instances may
interfere with each other - stopping or restarting the ring at unexpected
times.
Add a mutex so that hci_dma_dequeue_xfer() is serialized with respect to
itself. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Correct RING_CTRL_ABORT handling in DMA dequeue
The logic used to abort the DMA ring contains several flaws:
1. The driver unconditionally issues a ring abort even when the ring has
already stopped.
2. The completion used to wait for abort completion is never
re-initialized, resulting in incorrect wait behavior.
3. The abort sequence unintentionally clears RING_CTRL_ENABLE, which
resets hardware ring pointers and disrupts the controller state.
4. If the ring is already stopped, the abort operation should be
considered successful without attempting further action.
Fix the abort handling by checking whether the ring is running before
issuing an abort, re-initializing the completion when needed, ensuring that
RING_CTRL_ENABLE remains asserted during abort, and treating an already
stopped ring as a successful condition. |
| In the Linux kernel, the following vulnerability has been resolved:
media: verisilicon: Avoid G2 bus error while decoding H.264 and HEVC
For the i.MX8MQ platform, there is a hardware limitation: the g1 VPU and
g2 VPU cannot decode simultaneously; otherwise, it will cause below bus
error and produce corrupted pictures, even potentially lead to system hang.
[ 110.527986] hantro-vpu 38310000.video-codec: frame decode timed out.
[ 110.583517] hantro-vpu 38310000.video-codec: bus error detected.
Therefore, it is necessary to ensure that g1 and g2 operate alternately.
This allows for successful multi-instance decoding of H.264 and HEVC.
To achieve this, g1 and g2 share the same v4l2_m2m_dev, and then the
v4l2_m2m_dev can handle the scheduling. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not ASSERT() when the fs flips RO inside btrfs_repair_io_failure()
[BUG]
There is a bug report that when btrfs hits ENOSPC error in a critical
path, btrfs flips RO (this part is expected, although the ENOSPC bug
still needs to be addressed).
The problem is after the RO flip, if there is a read repair pending, we
can hit the ASSERT() inside btrfs_repair_io_failure() like the following:
BTRFS info (device vdc): relocating block group 30408704 flags metadata|raid1
------------[ cut here ]------------
BTRFS: Transaction aborted (error -28)
WARNING: fs/btrfs/extent-tree.c:3235 at __btrfs_free_extent.isra.0+0x453/0xfd0, CPU#1: btrfs/383844
Modules linked in: kvm_intel kvm irqbypass
[...]
---[ end trace 0000000000000000 ]---
BTRFS info (device vdc state EA): 2 enospc errors during balance
BTRFS info (device vdc state EA): balance: ended with status: -30
BTRFS error (device vdc state EA): parent transid verify failed on logical 30556160 mirror 2 wanted 8 found 6
BTRFS error (device vdc state EA): bdev /dev/nvme0n1 errs: wr 0, rd 0, flush 0, corrupt 10, gen 0
[...]
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
------------[ cut here ]------------
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
kernel BUG at fs/btrfs/bio.c:938!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 868 Comm: kworker/u8:13 Tainted: G W N 6.19.0-rc6+ #4788 PREEMPT(full)
Tainted: [W]=WARN, [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Workqueue: btrfs-endio simple_end_io_work
RIP: 0010:btrfs_repair_io_failure.cold+0xb2/0x120
RSP: 0000:ffffc90001d2bcf0 EFLAGS: 00010246
RAX: 0000000000000051 RBX: 0000000000001000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8305cf42 RDI: 00000000ffffffff
RBP: 0000000000000002 R08: 00000000fffeffff R09: ffffffff837fa988
R10: ffffffff8327a9e0 R11: 6f69747265737361 R12: ffff88813018d310
R13: ffff888168b8a000 R14: ffffc90001d2bd90 R15: ffff88810a169000
FS: 0000000000000000(0000) GS:ffff8885e752c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
------------[ cut here ]------------
[CAUSE]
The cause of -ENOSPC error during the test case btrfs/124 is still
unknown, although it's known that we still have cases where metadata can
be over-committed but can not be fulfilled correctly, thus if we hit
such ENOSPC error inside a critical path, we have no choice but abort
the current transaction.
This will mark the fs read-only.
The problem is inside the btrfs_repair_io_failure() path that we require
the fs not to be mount read-only. This is normally fine, but if we are
doing a read-repair meanwhile the fs flips RO due to a critical error,
we can enter btrfs_repair_io_failure() with super block set to
read-only, thus triggering the above crash.
[FIX]
Just replace the ASSERT() with a proper return if the fs is already
read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
alpha: fix user-space corruption during memory compaction
Alpha systems can suffer sporadic user-space crashes and heap
corruption when memory compaction is enabled.
Symptoms include SIGSEGV, glibc allocator failures (e.g. "unaligned
tcache chunk"), and compiler internal errors. The failures disappear
when compaction is disabled or when using global TLB invalidation.
The root cause is insufficient TLB shootdown during page migration.
Alpha relies on ASN-based MM context rollover for instruction cache
coherency, but this alone is not sufficient to prevent stale data or
instruction translations from surviving migration.
Fix this by introducing a migration-specific helper that combines:
- MM context invalidation (ASN rollover),
- immediate per-CPU TLB invalidation (TBI),
- synchronous cross-CPU shootdown when required.
The helper is used only by migration/compaction paths to avoid changing
global TLB semantics.
Additionally, update flush_tlb_other(), pte_clear(), to use
READ_ONCE()/WRITE_ONCE() for correct SMP memory ordering.
This fixes observed crashes on both UP and SMP Alpha systems. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: move wait_on_sem() out of spinlock
With iommu.strict=1, the existing completion wait path can cause soft
lockups under stressed environment, as wait_on_sem() busy-waits under the
spinlock with interrupts disabled.
Move the completion wait in iommu_completion_wait() out of the spinlock.
wait_on_sem() only polls the hardware-updated cmd_sem and does not require
iommu->lock, so holding the lock during the busy wait unnecessarily
increases contention and extends the time with interrupts disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: chipidea: udc: fix DMA and SG cleanup in _ep_nuke()
The ChipIdea UDC driver can encounter "not page aligned sg buffer"
errors when a USB device is reconnected after being disconnected
during an active transfer. This occurs because _ep_nuke() returns
requests to the gadget layer without properly unmapping DMA buffers
or cleaning up scatter-gather bounce buffers.
Root cause:
When a disconnect happens during a multi-segment DMA transfer, the
request's num_mapped_sgs field and sgt.sgl pointer remain set with
stale values. The request is returned to the gadget driver with status
-ESHUTDOWN but still has active DMA state. If the gadget driver reuses
this request on reconnect without reinitializing it, the stale DMA
state causes _hardware_enqueue() to skip DMA mapping (seeing non-zero
num_mapped_sgs) and attempt to use freed/invalid DMA addresses,
leading to alignment errors and potential memory corruption.
The normal completion path via _hardware_dequeue() properly calls
usb_gadget_unmap_request_by_dev() and sglist_do_debounce() before
returning the request. The _ep_nuke() path must do the same cleanup
to ensure requests are returned in a clean, reusable state.
Fix:
Add DMA unmapping and bounce buffer cleanup to _ep_nuke() to mirror
the cleanup sequence in _hardware_dequeue():
- Call usb_gadget_unmap_request_by_dev() if num_mapped_sgs is set
- Call sglist_do_debounce() with copy=false if bounce buffer exists
This ensures that when requests are returned due to endpoint shutdown,
they don't retain stale DMA mappings. The 'false' parameter to
sglist_do_debounce() prevents copying data back (appropriate for
shutdown path where transfer was aborted). |
| In the Linux kernel, the following vulnerability has been resolved:
9p/xen: protect xen_9pfs_front_free against concurrent calls
The xenwatch thread can race with other back-end change notifications
and call xen_9pfs_front_free() twice, hitting the observed general
protection fault due to a double-free. Guard the teardown path so only
one caller can release the front-end state at a time, preventing the
crash.
This is a fix for the following double-free:
[ 27.052347] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[ 27.052357] CPU: 0 UID: 0 PID: 32 Comm: xenwatch Not tainted 6.18.0-02087-g51ab33fc0a8b-dirty #60 PREEMPT(none)
[ 27.052363] RIP: e030:xen_9pfs_front_free+0x1d/0x150
[ 27.052368] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 41 55 41 54 55 48 89 fd 48 c7 c7 48 d0 92 85 53 e8 cb cb 05 00 48 8b 45 08 48 8b 55 00 <48> 3b 28 0f 85 f9 28 35 fe 48 3b 6a 08 0f 85 ef 28 35 fe 48 89 42
[ 27.052377] RSP: e02b:ffffc9004016fdd0 EFLAGS: 00010246
[ 27.052381] RAX: 6b6b6b6b6b6b6b6b RBX: ffff88800d66e400 RCX: 0000000000000000
[ 27.052385] RDX: 6b6b6b6b6b6b6b6b RSI: 0000000000000000 RDI: 0000000000000000
[ 27.052389] RBP: ffff88800a887040 R08: 0000000000000000 R09: 0000000000000000
[ 27.052393] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888009e46b68
[ 27.052397] R13: 0000000000000200 R14: 0000000000000000 R15: ffff88800a887040
[ 27.052404] FS: 0000000000000000(0000) GS:ffff88808ca57000(0000) knlGS:0000000000000000
[ 27.052408] CS: e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 27.052412] CR2: 00007f9714004360 CR3: 0000000004834000 CR4: 0000000000050660
[ 27.052418] Call Trace:
[ 27.052420] <TASK>
[ 27.052422] xen_9pfs_front_changed+0x5d5/0x720
[ 27.052426] ? xenbus_otherend_changed+0x72/0x140
[ 27.052430] ? __pfx_xenwatch_thread+0x10/0x10
[ 27.052434] xenwatch_thread+0x94/0x1c0
[ 27.052438] ? __pfx_autoremove_wake_function+0x10/0x10
[ 27.052442] kthread+0xf8/0x240
[ 27.052445] ? __pfx_kthread+0x10/0x10
[ 27.052449] ? __pfx_kthread+0x10/0x10
[ 27.052452] ret_from_fork+0x16b/0x1a0
[ 27.052456] ? __pfx_kthread+0x10/0x10
[ 27.052459] ret_from_fork_asm+0x1a/0x30
[ 27.052463] </TASK>
[ 27.052465] Modules linked in:
[ 27.052471] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
vhost: move vdpa group bound check to vhost_vdpa
Remove duplication by consolidating these here. This reduces the
posibility of a parent driver missing them.
While we're at it, fix a bug in vdpa_sim where a valid ASID can be
assigned to a group equal to ngroups, causing an out of bound write. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: fix zero-frag skb in frag_list on partial sendmsg error
Syzkaller reported a warning in kcm_write_msgs() when processing a
message with a zero-fragment skb in the frag_list.
When kcm_sendmsg() fills MAX_SKB_FRAGS fragments in the current skb,
it allocates a new skb (tskb) and links it into the frag_list before
copying data. If the copy subsequently fails (e.g. -EFAULT from
user memory), tskb remains in the frag_list with zero fragments:
head skb (msg being assembled, NOT yet in sk_write_queue)
+-----------+
| frags[17] | (MAX_SKB_FRAGS, all filled with data)
| frag_list-+--> tskb
+-----------+ +----------+
| frags[0] | (empty! copy failed before filling)
+----------+
For SOCK_SEQPACKET with partial data already copied, the error path
saves this message via partial_message for later completion. For
SOCK_SEQPACKET, sock_write_iter() automatically sets MSG_EOR, so a
subsequent zero-length write(fd, NULL, 0) completes the message and
queues it to sk_write_queue. kcm_write_msgs() then walks the
frag_list and hits:
WARN_ON(!skb_shinfo(skb)->nr_frags)
TCP has a similar pattern where skbs are enqueued before data copy
and cleaned up on failure via tcp_remove_empty_skb(). KCM was
missing the equivalent cleanup.
Fix this by tracking the predecessor skb (frag_prev) when allocating
a new frag_list entry. On error, if the tail skb has zero frags,
use frag_prev to unlink and free it in O(1) without walking the
singly-linked frag_list. frag_prev is safe to dereference because
the entire message chain is only held locally (or in kcm->seq_skb)
and is not added to sk_write_queue until MSG_EOR, so the send path
cannot free it underneath us.
Also change the WARN_ON to WARN_ON_ONCE to avoid flooding the log
if the condition is somehow hit repeatedly.
There are currently no KCM selftests in the kernel tree; a simple
reproducer is available at [1].
[1] https://gist.github.com/mrpre/a94d431c757e8d6f168f4dd1a3749daa |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: prevent races in ->query_interfaces()
It was possible for two query interface works to be concurrently trying
to update the interfaces.
Prevent this by checking and updating iface_last_update under
iface_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix locking usage for tcon fields
We used to use the cifs_tcp_ses_lock to protect a lot of objects
that are not just the server, ses or tcon lists. We later introduced
srv_lock, ses_lock and tc_lock to protect fields within the
corresponding structs. This was done to provide a more granular
protection and avoid unnecessary serialization.
There were still a couple of uses of cifs_tcp_ses_lock to provide
tcon fields. In this patch, I've replaced them with tc_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: validate sequence number of TX release report
Hardware rarely reports abnormal sequence number in TX release report,
which will access out-of-bounds of wd_ring->pages array, causing NULL
pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 1085 Comm: irq/129-rtw89_p Tainted: G S U
6.1.145-17510-g2f3369c91536 #1 (HASH:69e8 1)
Call Trace:
<IRQ>
rtw89_pci_release_tx+0x18f/0x300 [rtw89_pci (HASH:4c83 2)]
rtw89_pci_napi_poll+0xc2/0x190 [rtw89_pci (HASH:4c83 2)]
net_rx_action+0xfc/0x460 net/core/dev.c:6578 net/core/dev.c:6645 net/core/dev.c:6759
handle_softirqs+0xbe/0x290 kernel/softirq.c:601
? rtw89_pci_interrupt_threadfn+0xc5/0x350 [rtw89_pci (HASH:4c83 2)]
__local_bh_enable_ip+0xeb/0x120 kernel/softirq.c:499 kernel/softirq.c:423
</IRQ>
<TASK>
rtw89_pci_interrupt_threadfn+0xf8/0x350 [rtw89_pci (HASH:4c83 2)]
? irq_thread+0xa7/0x340 kernel/irq/manage.c:0
irq_thread+0x177/0x340 kernel/irq/manage.c:1205 kernel/irq/manage.c:1314
? thaw_kernel_threads+0xb0/0xb0 kernel/irq/manage.c:1202
? irq_forced_thread_fn+0x80/0x80 kernel/irq/manage.c:1220
kthread+0xea/0x110 kernel/kthread.c:376
? synchronize_irq+0x1a0/0x1a0 kernel/irq/manage.c:1287
? kthread_associate_blkcg+0x80/0x80 kernel/kthread.c:331
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
To prevent crash, validate rpp_info.seq before using. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6asm: drop DSP responses for closed data streams
'Commit a354f030dbce ("ASoC: qcom: q6asm: handle the responses
after closing")' attempted to ignore DSP responses arriving
after a stream had been closed.
However, those responses were still handled, causing lockups.
Fix this by unconditionally dropping all DSP responses associated with
closed data streams. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix signededness bug in smb_direct_prepare_negotiation()
smb_direct_prepare_negotiation() casts an unsigned __u32 value
from sp->max_recv_size and req->preferred_send_size to a signed
int before computing min_t(int, ...). A maliciously provided
preferred_send_size of 0x80000000 will return as smaller than
max_recv_size, and then be used to set the maximum allowed
alowed receive size for the next message.
By sending a second message with a large value (>1420 bytes)
the attacker can then achieve a heap buffer overflow.
This fix replaces min_t(int, ...) with min_t(u32) |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: remove xfs_attr_leaf_hasname
The calling convention of xfs_attr_leaf_hasname() is problematic, because
it returns a NULL buffer when xfs_attr3_leaf_read fails, a valid buffer
when xfs_attr3_leaf_lookup_int returns -ENOATTR or -EEXIST, and a
non-NULL buffer pointer for an already released buffer when
xfs_attr3_leaf_lookup_int fails with other error values.
Fix this by simply open coding xfs_attr_leaf_hasname in the callers, so
that the buffer release code is done by each caller of
xfs_attr3_leaf_read. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mixer: oss: Add card disconnect checkpoints
ALSA OSS mixer layer calls the kcontrol ops rather individually, and
pending calls might be not always caught at disconnecting the device.
For avoiding the potential UAF scenarios, add sanity checks of the
card disconnection at each entry point of OSS mixer accesses. The
rwsem is taken just before that check, hence the rest context should
be covered by that properly. |
