| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
9p: fix access mode flags being ORed instead of replaced
Since commit 1f3e4142c0eb ("9p: convert to the new mount API"),
v9fs_apply_options() applies parsed mount flags with |= onto flags
already set by v9fs_session_init(). For 9P2000.L, session_init sets
V9FS_ACCESS_CLIENT as the default, so when the user mounts with
"access=user", both bits end up set. Access mode checks compare
against exact values, so having both bits set matches neither mode.
This causes v9fs_fid_lookup() to fall through to the default switch
case, using INVALID_UID (nobody/65534) instead of current_fsuid()
for all fid lookups. Root is then unable to chown or perform other
privileged operations.
Fix by clearing the access mask before applying the user's choice. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: frag: disallow unicast fragment in fragment
batadv_frag_skb_buffer() is called by batadv_batman_skb_recv() when a
BATADV_UNICAST_FRAG packet is received. Once all fragments are collected
and the packet is reassembled, batadv_recv_frag_packet() calls
batadv_batman_skb_recv() again to process the defragmented payload.
A malicious sender can craft a BATADV_UNICAST_FRAG packet whose reassembled
payload is itself a BATADV_UNICAST_FRAG packet (matryoshka-style nesting).
Each nesting level recurses through batadv_batman_skb_recv() without bound,
growing the kernel stack until it is exhausted.
Since refragmentation or fragments in fragments are not actually allowed,
discard all packets which are still BATADV_UNICAST_FRAG packets after the
defragmentation process. |
| A race condition was discovered in ext4_write_inline_data_end in fs/ext4/inline.c in the ext4 subsystem in the Linux kernel through 5.13.13. |
| A use-after-free exists in the Linux Kernel in tc_new_tfilter that could allow a local attacker to gain privilege escalation. The exploit requires unprivileged user namespaces. We recommend upgrading past commit 04c2a47ffb13c29778e2a14e414ad4cb5a5db4b5 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-ep-msi: Fix error unwind and prevent double alloc
pci_epf_alloc_doorbell() stores the allocated doorbell message array in
epf->db_msg/epf->num_db before requesting MSI vectors. If MSI allocation
fails, the array is freed but the EPF state may still point to freed
memory.
Clear epf->db_msg and epf->num_db on the MSI allocation failure path so
that later cleanup cannot double-free the array and callers can retry
allocation.
Also return -EBUSY when doorbells have already been allocated to prevent
leaking or overwriting an existing allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
power: reset: linkstation-poweroff: fix use-after-free in the linkstation_poweroff_init()
Move of_node_put(dn) after the of_match_node() call, which still needs
the node pointer. The node reference is correctly released after use. |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: smp: report dying CPU to RCU in stop_this_cpu()
smp_send_stop() parks all secondary CPUs in stop_this_cpu(). The function
marks the CPU offline for the scheduler via set_cpu_online(false) but
never informs RCU, so RCU keeps expecting a quiescent state from CPUs
that are now spinning forever with interrupts disabled.
As long as nothing waits for an RCU grace period after smp_send_stop()
this is harmless, which is why it went unnoticed. Since commit
91840be8f710 ("irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT")
however, irq_work_sync() calls synchronize_rcu() on architectures without
an irq_work self-IPI, i.e. where arch_irq_work_has_interrupt() returns
false. That is the asm-generic default used by MIPS. Any irq_work_sync()
issued in the reboot/shutdown path after smp_send_stop() then blocks on
a grace period that can never complete, hanging the reboot:
WARNING: CPU: 0 PID: 15 at kernel/irq_work.c:144 irq_work_queue_on
...
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
rcu: Offline CPU 1 blocking current GP.
rcu: Offline CPU 2 blocking current GP.
rcu: Offline CPU 3 blocking current GP.
This issue was noticed on several Realtek MIPS switch SoCs (MIPS
interAptiv) and came up during kernel bump downstream in OpenWrt from
6.18.33 to 6.18.34, after the backport of the patch to the 6.18 stable
branch. The patch also has been backported all the way back to 6.1.
Call rcutree_report_cpu_dead() once interrupts are disabled, mirroring the
generic CPU-hotplug offline path, so RCU stops waiting on the parked CPUs
and grace periods can still complete. MIPS shuts down all CPUs here
without going through the CPU-hotplug mechanism, so this report is not
otherwise issued. Reporting a dying CPU to RCU outside the regular hotplug
offline path is not unprecedented: arm64 does the same in cpu_die_early().
There it is an exception for a CPU that was coming online and is aborting
bringup, rather than the default shutdown action as on MIPS. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: region: fix use-after-free in child_regions_with_firmware()
Move of_node_put(child_region) after the error print to avoid accessing
freed memory when pr_err() references child_region.
[ Yilun: Fix the Fixes tag ] |
| In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx-lpi2c: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rc: igorplugusb: fix control request setup packet
Commit eac69475b01f ("media: rc: igorplugusb: heed coherency
rules") changed the control request storage from an embedded struct to
an allocated pointer so it can obey DMA coherency rules.
However, the driver still passes &ir->request to usb_fill_control_urb().
That points the URB setup packet at the pointer field itself rather than
at the allocated struct usb_ctrlrequest.
USB core then interprets pointer bytes as the setup packet. This can
produce an invalid bRequestType and trigger the control direction warning
reported by syzbot:
usb 2-1: BOGUS control dir, pipe 80003580 doesn't match bRequestType 0
Pass ir->request itself as the setup packet. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: net2280: Fix double free in probe error path
usb_initialize_gadget() installs gadget_release() as the release
callback for the embedded gadget device. The struct net2280 instance is
therefore released through gadget_release() when the gadget device's last
reference is dropped.
The probe error path calls net2280_remove(), which tears down the
partially initialized device and drops the gadget reference with
usb_put_gadget(). Calling kfree(dev) afterwards can free the same object
again.
Drop the explicit kfree() and let the gadget device release callback
handle the final free. This issue was found by a static analysis tool
I am developing. |
| In the Linux kernel, the following vulnerability has been resolved:
net: psp: require admin permission for dev-set and key-rotate
The dev-set and key-rotate netlink operations modify shared device
state (PSP version configuration and cryptographic key material,
respectively) but do not require CAP_NET_ADMIN. The only access
control is psp_dev_check_access() which merely verifies netns
membership. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: wake sq waiters when the transport closes
Threads parked in svc_rdma_sq_wait() on sc_sq_ticket_wait or
sc_send_wait can hang indefinitely in TASK_UNINTERRUPTIBLE state
across transport teardown, pinning svc_xprt references and
blocking svc_rdma_free().
The close path sets XPT_CLOSE before invoking xpo_detach and both
wait_event predicates include an XPT_CLOSE term, but the
predicates are re-evaluated only on wakeup. sc_sq_ticket_wait has
no completion-driven wake path; it is advanced solely by the
chained ticket handoff inside svc_rdma_sq_wait() itself. Without
an explicit wake at close, parked threads never observe
XPT_CLOSE, hold their svc_xprt_get reference forever, and
svc_rdma_free() blocks on xpt_ref dropping to zero.
Two close entry points reach this transport. Local teardown runs
svc_rdma_detach() from svc_handle_xprt() -> svc_delete_xprt() ->
xpo_detach() on a worker thread. A remote disconnect arrives at
svc_rdma_cma_handler(), which calls svc_xprt_deferred_close():
that sets XPT_CLOSE and enqueues the transport but does not
access either RDMA waitqueue, so a worker already parked in
svc_rdma_sq_wait() never re-evaluates its predicate. With every
worker parked on this transport, no thread is available to run
the local teardown either, and the wake site there is
unreachable.
Introduce svc_rdma_xprt_deferred_close(), a thin svcrdma wrapper
that calls svc_xprt_deferred_close() and then wakes both
sc_sq_ticket_wait and sc_send_wait. Convert the svcrdma producers
that called svc_xprt_deferred_close() directly:
svc_rdma_cma_handler(), qp_event_handler(),
svc_rdma_post_send_err(), svc_rdma_wc_send(), the sendto drop
path, the rw completion error paths, and the recvfrom flush and
read-list error paths.
Wake both waitqueues from svc_rdma_detach() as well. The
synchronous svc_xprt_close() path (backchannel ENOTCONN, device
removal via svc_rdma_xprt_done) reaches detach without flowing
through svc_xprt_deferred_close() and therefore does not invoke
the new helper.
[ cel: add svc_rdma_xprt_deferred_close() to complete the fix ] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Don't leak PFN when kvm_translate_vncr() races MMU notifier
In the case that kvm_translate_vncr() races with an MMU notifier the
early return does not release a reference on the faulted in PFN. Add
the necessary call to kvm_release_faultin_page() for the unused PFN. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ti: icssm-prueth: fix eth_ports_node leak in probe
The error path on of_property_read_u32() failure inside
icssm_prueth_probe() returns without putting eth_ports_node,
which was acquired before the for_each_child_of_node() loop.
Drop it before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: tracepoints: fix sleep while in atomic context in btrfs_sync_file()
The trace event btrfs_sync_file() is called in an atomic context (all trace
events are) and its call to dput(), which is needed due to the call to
dget_parent(), can sleep, triggering a kernel splat.
This can be reproduced by enabling the trace event and running btrfs/056
from fstests for example. The splat shown in dmesg is the following:
[53.919] BUG: sleeping function called from invalid context at fs/dcache.c:970
[53.947] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 32773, name: xfs_io
[53.988] preempt_count: 2, expected: 0
[53.967] RCU nest depth: 0, expected: 0
[53.943] Preemption disabled at:
[53.944] [<0000000000000000>] 0x0
[54.078] CPU: 0 UID: 0 PID: 32773 Comm: xfs_io Tainted: G W 7.1.0-rc1-btrfs-next-232+ #1 PREEMPT(full)
[54.070] Tainted: [W]=WARN
[54.071] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[54.072] Call Trace:
[54.074] <TASK>
[54.076] dump_stack_lvl+0x56/0x80
[54.079] __might_resched.cold+0xd6/0x10f
[54.072] dput.part.0+0x24/0x110
[54.078] trace_event_raw_event_btrfs_sync_file+0x75/0x140 [btrfs]
[54.089] btrfs_sync_file+0x1ed/0x530 [btrfs]
[54.087] ? __handle_mm_fault+0x8ae/0xed0
[54.089] btrfs_do_write_iter+0x172/0x210 [btrfs]
[54.091] vfs_write+0x21f/0x450
[54.094] __x64_sys_pwrite64+0x8d/0xc0
[54.096] ? do_user_addr_fault+0x20c/0x670
[54.099] do_syscall_64+0x60/0xf20
[54.092] ? clear_bhb_loop+0x60/0xb0
[54.094] entry_SYSCALL_64_after_hwframe+0x76/0x7e
So stop using dget_parent() and dput() and access the parent dentry
directly as dentry->d_parent. This is also what ext4 is doing in
its equivalent trace event ext4_sync_file_enter(). |
| In the Linux kernel, the following vulnerability has been resolved:
phonet/pep: disable BH around forwarded sk_receive_skb()
The networking receive path is usually run from softirq context, but
protocols that take the socket lock may have packets stored in the
backlog and processed later from process context. In that case
release_sock() -> __release_sock() drops the slock with spin_unlock_bh()
and then calls sk->sk_backlog_rcv() with bottom halves enabled.
Typical sk_backlog_rcv handlers process the socket whose backlog is
being drained, so the BH state at entry is irrelevant for the slocks
they touch. pep_do_rcv() is different: when the inbound skb targets an
existing PEP pipe, it forwards the skb to a different *child* socket
via sk_receive_skb(). That helper takes the child slock with
bh_lock_sock_nested(), which is just spin_lock_nested() and assumes BH
is already off. The same child slock therefore ends up acquired with
BH on (process path) and with BH off (softirq path):
process context softirq context
--------------- ---------------
release_sock(listener) __netif_receive_skb()
__release_sock() phonet_rcv()
spin_unlock_bh() __sk_receive_skb(listener)
[BH now ENABLED] [BH already disabled]
sk_backlog_rcv: sk_backlog_rcv:
pep_do_rcv() pep_do_rcv()
sk_receive_skb(child) sk_receive_skb(child)
bh_lock_sock_nested(child) bh_lock_sock_nested(child)
=> SOFTIRQ-ON-W => IN-SOFTIRQ-W
Lockdep flags this as inconsistent lock state, and it can become a real
self-deadlock if a softirq on the same CPU tries to receive to the same
child socket while its slock is held in the BH-enabled path:
WARNING: inconsistent lock state
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
(slock-AF_PHONET/1){+.?.}-{3:3}, at: __sk_receive_skb+0x1cf/0x900
__sk_receive_skb net/core/sock.c:563
sk_receive_skb include/net/sock.h:2022 [inline]
pep_do_rcv net/phonet/pep.c:675
sk_backlog_rcv include/net/sock.h:1190
__release_sock net/core/sock.c:3216
release_sock net/core/sock.c:3815
pep_sock_accept net/phonet/pep.c:879
Wrap the forwarded sk_receive_skb() in local_bh_disable() /
local_bh_enable() so the child slock is always acquired with BH off.
local_bh_disable() nests safely on the softirq path.
Discovered via in-house syzkaller fuzzing; the same root cause also
on the linux-6.1.y syzbot dashboard as extid 44f0626dd6284f02663c.
Reproduced under KASAN + LOCKDEP + PROVE_LOCKING, reproducer:
https://pastebin.com/A3t8xzCR |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Disable AVIC IPI virtualization on Hygon Family 18h (erratum #1235)
Hygon Family 18h CPUs are derived from AMD Family 17h (Zen1) silicon and
share the same erratum #1235: hardware may read a stale IsRunning=1 bit
during ICR write emulation and silently fail to generate an
AVIC_IPI_FAILURE_TARGET_NOT_RUNNING VM-Exit on the sending vCPU.
The absence of the VM-Exit causes KVM to miss the required wakeup of
blocking target vCPUs, leading to hung vCPUs and unbounded delays in
guest execution.
Extend the existing AMD Family 17h erratum #1235 workaround to also cover
Hygon Family 18h. With IPI virtualization disabled, KVM never sets
IsRunning=1 in the Physical ID table, so every non-self IPI generates a
VM-Exit and is correctly emulated. |
