| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Integer Overflow or Wraparound vulnerability in Cesanta Mongoose Web Server v7.14 allows an attacker to send an unexpected TLS packet and produce a segmentation fault on the application. |
| Net::IP::LPM versions before 1.11 for Perl allow a heap out-of-bounds read via an unbounded prefix length.
add() passes the prefix string to the trie builder addPrefixToTrie() without checking it against the address width.
addPrefixToTrie() then walks the prefix buffer by prefix_length bits, reading prefix[byte] for byte up to prefix_len/8, where prefix is the 4-byte (IPv4) or 16-byte (IPv6) packed address. A prefix length greater than 32 for IPv4 or 128 for IPv6, for example add("1.2.3.4/255", $v) or add("2001:db8::/255", $v), reads past the end of the packed address.
The out-of-bounds read happens during trie construction and is bounded: the prefix length is stored as an unsigned char, so the bit walk reads at most 32 bytes from the start of the packed address, a short distance past the end of the 4-byte or 16-byte buffer. It is detectable under AddressSanitizer, valgrind, or a hardened allocator, where it can abort the process. Lookups and dump() format only the valid address width, so the out-of-bounds bytes are not exposed through the module's API. |
| Net::IP::LPM version 1.10 for Perl does not properly consider leading zero characters in IP CIDR address strings, which could allow attackers to bypass access control that is based on IP addresses.
Leading zeros are used to indicate octal numbers, which can confuse users who are intentionally using octal notation, as well as users who believe they are using decimal notation. |
| In Power HAL, there is a possible out of bounds write due to a missing bounds check. This could lead to local escalation of privilege if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11165543; Issue ID: MSV-9011. |
| In the Linux kernel, the following vulnerability has been resolved:
nsfs: tighten permission checks for handle opening
Even privileged services should not necessarily be able to see other
privileged service's namespaces so they can't leak information to each
other. Use may_see_all_namespaces() helper that centralizes this policy
until the nstree adapts. |
| Tobit Laboratories AG TeamDavid's Webbox application handles password changes using a function triggered by
including the string "(editini)" in the file path, writing the new
password to the specified "Archive.ini" file. However, the application
does not verify that the provided path actually refers to an
"Archive.ini" file. If an attacker specifies a different file with
excessive size, a buffer overflow occurs. This vulnerability allows an
unauthenticated attacker to crash the server, resulting in denial of
service. This issue affects TeamDavid before Rollout 528.
Starting with Rollout 528 (June 30, 2026), the affected functionality is disabled by default and the vulnerabilities are therefore no longer exposed through this functionality. |
| Out-of-bounds read vulnerability in Samsung Opensource rLottie allows Overread Buffers.
This issue affects rLottie: 25648aef19187b3f87f4d9420b8d761453ad4630. |
| toml-node is a TOML parser for Node.js and the browser. Prior to 4.1.2, toml.parse() in lib/compiler.js can be tricked by a table path such as a.b.y.__proto__.__proto__, allowing traversal from a scalar value into Number.prototype and Object.prototype. The currentPath tracking value uses both arrays and strings, so valueAssignments records a comma-joined path such as a,b.y while deepRef checks the dot-joined path a.b.y, allowing the duplicate-key guard to miss and attacker-controlled keys to be written to Object.prototype. A table-array prefix-clearing path in addTableArray can also erase guard state before the same __proto__ traversal. Injected properties become visible throughout the Node.js process and can cause denial of service, logic or authorization bypass, or code execution when an application contains a suitable gadget. This issue is fixed in version 4.1.2. |
| YesWiki is a wiki system written in PHP. Prior to version 4.6.6, the recentchanges action (actions/recentchanges.php) accepts a period argument from two disjoint parameter spaces. A whitelist validates only the URL form against ['day','week','month']. The action-argument form takes the else branch with no validation, and the value flows into PageManager::getRecentlyChanged(), where it is interpolated into a WHERE time >= '...' ORDER BY time DESC clause without escaping or parameterization. UNION-based injection succeeds, the leaked rows render into the response page, so any visitor of the trigger page sees the exfiltrated data. The vulnerability provides arbitrary read of the YesWiki database to anyone who can save the trigger page. On a default install (default_write_acl='*'), this includes anonymous users, subject to the hashcash JS check on the page-edit form. Once the trigger page is saved, every subsequent view fires the injection as the SQLi is stored. Stored SQL injection is reachable through the page-edit flow, with arbitrary database read. This issue has been patched in version 4.6.6. |
| FreeRDP before 3.31.0 contains a heap out-of-bounds read vulnerability in the general_ChromaV1ToYUV444 function during AVC444 chroma plane reconstruction. A malicious RDP server can craft a RFX_AVC444_BITMAP_STREAM with specific frame geometry to trigger an out-of-bounds memory read past the allocated luma plane. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: microread: validate target discovery payload lengths
microread_target_discovered() parses target discovery payloads from
skb->data according to the HCI gate. The fixed field offsets and UID
copies were checked only against the destination nfc_target buffers, not
against the actual skb length.
Validate that each gate-specific payload contains the fixed fields and
UID bytes before reading or copying them. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: bound the connect_sn TLV walk to the skb
Commit 27256cdb290e ("nfc: llcp: bound SNL TLV parsing to the skb and
add length checks") fixed the unbounded TLV walk in nfc_llcp_recv_snl(),
and commit d8bd2dedbde5 ("nfc: llcp: fix OOB read and u8 offset wrap in
TLV parsers") subsequently bounded nfc_llcp_parse_gb_tlv() and
nfc_llcp_parse_connection_tlv(). One sibling parser sharing the same
pattern remains unbounded: nfc_llcp_connect_sn().
nfc_llcp_connect_sn() walks a TLV list, reading a two-byte header
(type, length) followed by length bytes of value, without checking that
the two header bytes or the declared length stay within the buffer. It
returns a pointer to a service name of up to 255 bytes that may point
past the end of the skb; it is subsequently consumed by memcmp() in
nfc_llcp_sock_from_sn(). In addition tlv_array_len was computed as
"skb->len - LLCP_HEADER_SIZE" in size_t, so a CONNECT/CC frame shorter
than the LLCP header underflows to a huge length and the walk runs far
past the buffer.
nfc_llcp_connect_sn() is reachable from nfc_llcp_recv_connect() and
nfc_llcp_recv_cc(), i.e. from received CONNECT and CC PDUs. A nearby
NFC device can reach this without authentication; LLCP link activation
happens automatically after NFC-DEP, and the nfc_llcp_rx_skb()
dispatcher applies no minimum-length guard.
Walk the TLV list by pointer, bounded by skb_tail_pointer(skb), and
validate each declared length before use, matching the approach already
used for nfc_llcp_recv_snl(). Starting the walk at
&skb->data[LLCP_HEADER_SIZE] against the tail pointer also removes the
size_t underflow for short frames.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: fdp: bound the device-reported read length and fix an skb leak
fdp_nci_i2c_read() takes the next packet length from two device-supplied
bytes and never validates it. The value is a u16 used as the
i2c_master_recv() count into a 261-byte on-stack buffer: a malicious,
counterfeit or malfunctioning controller (or an i2c bus interposer) can
drive it far past the buffer for a stack out-of-bounds write that
clobbers the canary and return address, or below the minimum frame size
(directly, or by truncating the computed sum) so the header/LRC strip
and the next length read run past a short receive. Reject a length
outside [FDP_NCI_I2C_MIN_PAYLOAD, FDP_NCI_I2C_MAX_PAYLOAD], as a
corrupted packet already is, and force resynchronization.
The same loop allocates one data skb per iteration and assumes a length
packet followed by a data packet; a device that sends two data packets
in one call leaks the first skb when the second allocation overwrites
it. Free a previously allocated skb before allocating the next. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: nintendo: fix out-of-bounds read in joycon_ctlr_read_handler()
joycon_ctlr_read_handler() casts an incoming HID input report to
struct joycon_input_report and parses it, guarding the cast only with a
12-byte length check:
if (size >= 12) /* make sure it contains the input report */
joycon_parse_report(ctlr, (struct joycon_input_report *)data);
struct joycon_input_report is 49 bytes: a 13-byte header followed by a
union whose IMU arm is 36 bytes. For an IMU report joycon_parse_report()
-> joycon_parse_imu_report() walks that union (struct offsets 13..48),
so a report of exactly 12 bytes with data[0] == JC_INPUT_IMU_DATA passes
the guard yet is read up to 37 bytes past its declared length. The
over-read bytes are decoded into accelerometer/gyroscope values and
forwarded to userspace through the "(IMU)" input device, leaking
driver-internal memory. data[0] and size are fully controlled by a
malicious or spoofed Joy-Con/Pro Controller.
Receive buffers are sized to the maximum report length, so this is an
over-read within the allocation rather than a slab OOB, but the decoded
bytes still reach userspace.
The sibling subcmd path in joycon_ctlr_handle_event() already bounds the
same cast correctly:
if (size < sizeof(struct joycon_input_report) ||
data[0] != JC_INPUT_SUBCMD_REPLY)
break;
Use the same sizeof(struct joycon_input_report) bound here. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: reject PDUs shorter than the LLCP header
Every LLCP PDU begins with a two-byte header (DSAP/SSAP + PTYPE), but the
receive path never checked that a frame is at least LLCP_HEADER_SIZE bytes
before parsing it.
nfc_llcp_rx_skb() reads the header via nfc_llcp_ptype()/nfc_llcp_dsap()/
nfc_llcp_ssap(), which dereference pdu->data[0] and pdu->data[1], and a
CONNECT or CC PDU then computes
tlv_array_len = skb->len - LLCP_HEADER_SIZE;
as a size_t and hands it to the TLV walk. When the frame is shorter than
the header the subtraction wraps to a huge value and the walk runs far
past the buffer, an out-of-bounds read.
A nearby NFC device can reach this without authentication; LLCP link
activation happens automatically after NFC-DEP.
Guard the common receive choke point __nfc_llcp_recv(), shared by both the
target (nfc_llcp_data_received()) and initiator (nfc_llcp_recv()) paths, so
a short skb is dropped before the rx_work worker parses it. Use
pskb_may_pull() rather than a skb->len test so the two header bytes are
guaranteed to sit in the skb linear area even for a non-linear skb,
matching how the sibling NCI and HCI receive paths validate their headers.
Reproduced with a KFENCE out-of-bounds read via /dev/virtual_nci on
linux-next.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Validate AIBV and AISB before pinning guest pages
The AIBV holds one bit per MSI-X vector for a given function. The size of
the bit vector is derived from the NOI and the AIBVO. If the size of the
AIBV exceeds a single page boundary, then reject the request as we cannot
safely pin the guest AIBV.
Similarly reject the request if the AISB address is not 8-byte aligned as
the architecture requires doubleword alignment for the summary bit address.
Since the AISBO can address up to 64 bits, the size of the AISB can only be
8 bytes for the function. This also ensures the AISB doesn't exceed a
single page boundary. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SDCA: Make UMP message size check more robust
If message offset was larger than the buffer length the size
check will pass incorrectly. Refactor the check such that it is
more robust to invalid sizes. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: lpass-wsa-macro: Fix enum kcontrol accesses
EAR SPKR PA Gain" and the four "WSA RX* Mux" controls are enumerated,
but their get and put callbacks access the value through
ucontrol->value.integer.value[0] (a long) instead of
ucontrol->value.enumerated.item[0] (an unsigned int).
This same pattern was fixed in the sibling drivers by
commit bcfe5f76cc40 ("ASoC: codecs: rx-macro: fix accessing array
out of bounds for enum type") and
commit 0ea5eff7c606 ("ASoC: codecs: va-macro: fix accessing array
out of bounds for enum type"), but wsa-macro was missed.
On 64-bit kernels with CONFIG_SND_CTL_DEBUG this trips the elem value
sanity check and every read of these controls fails with -EINVAL. |
| An issue in the NetStaX EtherNet/IP Stack prior to v5.6.1 could allow a large Class 3 explicit-message request to exceed the application-side receive buffer without generating an error or warning. The result could be memory corruption, a device crash, or a potential remote attack vector without the originating device receiving a CIP error indicating that the request could not be processed. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qce - fix CCM AAD buffer underallocation
The AAD buffer allocated in qce_aead_ccm_prepare_buf_assoclen()
can be smaller than the length later programmed into the DMA
scatterlist.
The allocation size is currently calculated as:
ALIGN(assoclen, 16) + MAX_CCM_ADATA_HEADER_LEN
while the DMA length is set to:
ALIGN(assoclen + adata_header_len, 16)
Since ALIGN() does not distribute over addition, the allocation
can be smaller than the DMA length. For example, when
assoclen = 32 and adata_header_len = 2:
allocation = ALIGN(32, 16) + 6 = 38
DMA length = ALIGN(32 + 2, 16) = 48
As a result, the QCE hardware can read beyond the allocated
buffer while computing the CBC-MAC over the associated data.
The extra bytes are folded into the authentication tag,
resulting in an incorrect tag and causing CCM self-test
failures such as:
alg: aead: ccm-aes-qce encryption test failed (wrong result)
on test vector 8
Fix the allocation by adding the maximum possible AAD header
length before alignment:
ALIGN(assoclen + MAX_CCM_ADATA_HEADER_LEN, 16)
This guarantees that the allocated buffer is large enough
for the fully padded AAD data for all supported header sizes. |
