| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
unshare: don't drop active namespace references that were never taken
Active references on the namespaces of an nsproxy are taken when the
nsproxy is installed into a task in switch_task_namespaces() and
copy_namespaces() and dropped again by put_nsproxy() through
deactivate_nsproxy().
But ksys_unshare() calls put_nsproxy() on an nsproxy that was never
installed when set_cred_ucounts() fails. The new namespaces of that
nsproxy go from zero to minus one and the namespaces shared with the
caller lose a reference that belongs to the nsproxy the caller keeps
using:
WARNING: kernel/nscommon.c:171 at __ns_ref_active_put+0x1cd/0x230
nsproxy_ns_active_put
deactivate_nsproxy
ksys_unshare
Afterwards the namespaces the caller lives in aren't listed by listns()
anymore. set_cred_ucounts() only fails when alloc_ucounts() can't
allocate and it only allocates when the real uid of the caller differs
from its effective uid.
Commit cefd55bd2159 ("nsproxy: fix free_nsproxy() and simplify
create_new_namespaces()") separated the two cases on purpose.
nsproxy_free() frees an nsproxy that was prepared but never installed
and that's what a failed setns() uses in put_nsset(). Export it and use
it for a failed unshare() as well. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmveth: h_free logical LAN on open-fail after register
ibmveth_open() registers the logical LAN, then allocates the RX
buffer pools. A pool failure jumps to out_free_buffer_pools without
h_free_logical_lan(), so PHYP still owns the buffer-list page when
it is unmapped. request_irq() failure already issued the hypercall
before taking the same label.
Move that h_free to the shared post-register unwind so both paths
deregister before the buffer list is unmapped. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix XSK buffer leak when rings are stopped
GVE does not free XSK buffers when resetting ring state as a part of
stopping queues. This causes all XSK buffers which are posted to the
NIC to be leaked.
Free XSK buffers attached to an allocated buf_state when stopping rings.
This issue was hit in production. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix napi_disable deadlock when attempting to disable XSK pools
When disabling XSK pools, GVE calls the unlocked versions of
napi_disable and napi_enable. However, the netdev lock has already been
acquired before ndo_bpf is called because GVE supports queue management
ops. Calling the unlocked versions of napi_disable/enable results in a
deadlock when attempting to disable XSK pools, as the thread attempts to
re-acquire a lock it already holds.
Update the NAPI calls to use the locked versions.
This issue was found in production. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: reject net_iov in zerocopy receive mapping hints
After copying a readable prefix, receive_fallback_to_copy() asks
tcp_zerocopy_set_hint_for_skb() where page mapping can resume. If the
next skb is unreadable, find_next_mappable_frag() passes its net_iov
fragment to can_map_frag().
skb_frag_page() returns NULL for a net_iov, but can_map_frag()
dereferences it in PageCompound(). A v7.2 KASAN run on a connected TCP
socket with 64 readable bytes followed by a 4096-byte NET_IOV_DMABUF
fragment reported:
BUG: KASAN: null-ptr-deref in can_map_frag
tcp_zerocopy_receive -> can_map_frag
Kernel panic - not syncing: KASAN: panic_on_warn set
The diagnostic inserted the net_iov directly because the test host has
no devmem-capable NIC. Hardware end-to-end reachability remains untested
and requires CONFIG_NET_DEVMEM plus a supported DMA-buf-bound RX queue.
Reject all net_iov fragments before skb_frag_page(). This covers both
DMABUF and IOURING net_iov types while leaving page-backed checks
unchanged. With the guard, the same queue copied the readable prefix,
returned a 4096-byte skip hint, and completed without a fault. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P device removal race in brcmf_detach()
When the driver is removed while the user space process that created
the P2P device (e.g. wpa_supplicant) is still exiting, the P2P device
interface is removed twice and the kernel crashes.
The two paths are:
- wpa_supplicant, on exit, sends NL80211_CMD_DEL_INTERFACE for the P2P
device. nl80211_del_interface() holds RTNL and the wiphy mutex and
calls brcmf_p2p_del_vif(), which disables discovery and waits up to
1.5 s for BRCMF_E_IF_DEL. Then it calls brcmf_remove_interface(),
which unregisters the wdev and frees the vif and the ifp.
- brcmf_detach() sets the bus down, so BRCMF_E_IF_DEL never arrives,
and calls brcmf_remove_interface(ifp, false) for the same ifp.
brcmf_p2p_ifp_removed() reads ifp->vif and then blocks on
rtnl_lock(). When brcmf_p2p_del_vif() releases RTNL, it calls
cfg80211_unregister_wdev() on the wdev that was already unregistered
and freed.
The second list_del_rcu() of wdev->list faults on LIST_POISON2:
brcmfmac: brcmf_p2p_del_vif delete P2P vif
brcmfmac: brcmf_p2p_deinit_discovery enter
brcmfmac: brcmf_p2p_del_vif P2P: GO_NEG_PHASE status cleared
brcmfmac: brcmf_detach Enter
brcmfmac: brcmf_bus_change_state 1 -> 0
brcmfmac: brcmf_remove_interface Enter, bsscfgidx=1, ifidx=0
brcmfmac: brcmf_del_if Enter, bsscfgidx=1, ifidx=0
brcmfmac: brcmf_p2p_ifp_removed P2P: device interface removed
[1.5 s later, brcmf_p2p_del_vif() timed out]
brcmfmac: brcmf_remove_interface Enter, bsscfgidx=1, ifidx=0
brcmfmac: brcmf_del_if Enter, bsscfgidx=1, ifidx=0
brcmfmac: brcmf_p2p_ifp_removed P2P: device interface removed
Unable to handle kernel paging request at virtual address dead000000000122
Internal error: Oops: 96000044 [#1] PREEMPT_RT SMP
pc : _cfg80211_unregister_wdev+0x6c/0x264 [cfg80211]
Call trace:
_cfg80211_unregister_wdev+0x6c/0x264 [cfg80211]
cfg80211_unregister_wdev+0x10/0x1c [cfg80211]
brcmf_p2p_ifp_removed+0x84/0xb0 [brcmfmac]
brcmf_remove_interface+0x1f4/0x254 [brcmfmac]
brcmf_detach+0x88/0x180 [brcmfmac]
brcmf_sdio_remove+0x90/0x7b0 [brcmfmac]
brcmf_sdiod_remove+0x20/0xa0 [brcmfmac]
brcmf_ops_sdio_remove+0xbc/0x12c [brcmfmac]
sdio_bus_remove+0x38/0x144
device_release_driver_internal+0x1e8/0x2c0
device_release_driver+0x14/0x20
brcmf_sdio_bus_remove+0x2c/0x40 [brcmfmac]
brcmf_fwvid_unregister_vendor+0xd8/0x170 [brcmfmac]
__exit_compat+0x18/0x418 [brcmfmac_cyw]
__arm64_sys_delete_module+0x1ac/0x244
The log was taken with debug=0x406 on an i.MX 8M Plus board with a
CYW55513 (Sona IF513) on SDIO. The driver is the Ezurio backport of
brcmfmac from v6.18.22 on a 5.4-rt kernel. The code involved is the same
in mainline.
To reproduce:
1. Start wpa_supplicant on wlan0 and let it associate. It creates the
P2P device (iw dev shows "type P2P-device").
2. Stop wpa_supplicant and remove the driver without waiting for
wpa_supplicant to exit:
kill $(pidof wpa_supplicant)
rmmod brcmfmac_cyw brcmfmac
The crash is reproducible on that board.
For the interface without a netdev (the P2P device), take RTNL and the
wiphy mutex in brcmf_detach() before reading iflist, and remove it with
locked=true. If brcmf_p2p_del_vif() runs first, brcmf_detach() finds the
slot empty. If brcmf_detach() runs first, nl80211 does not find the wdev
any more. The interfaces with a netdev are removed as before, because
brcmf_del_if() takes RTNL on its own for the primary interface. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: account only unread bytes in read_skb()
After a partial stream receive, rx_bytes tracks the unread suffix while
buf_used and peer credit still cover the whole packet.
virtio_transport_read_skb() dequeues that packet but passes pkt_len for
both counters, underflowing rx_bytes.
On a connected CID_LOCAL stream with an SK_SKB verdict, a 40-byte read
from a 100-byte packet made SIOCINQ report -40, an empty recv return
ELOOP, and poll report the empty socket readable. After verdict detach,
receiving 40 bytes wrapped the counter to zero and hid those queued bytes
until one more byte arrived. The fixed run kept the counter balanced
and exposed all queued data immediately.
This was found during an LLM-assisted manual source audit of VSOCK
receive accounting while re-evaluating virtio_transport_read_skb() after
CVE-2024-50169.
Subtract only skb->len minus the VSOCK offset from rx_bytes. Retain the
full packet length for buf_used and peer credit. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: Fix reference and vm_bo handling in remap()
When a map overlaps part of an existing mapping, pvr_vm_gpuva_remap()
splits the mapping into prev/next parts covering what the request did
not take, instead of creating something new. It gets two things wrong.
- A GEM reference is taken for each part but it's never needed and never
dropped, so it leaks one reference per split (remap-next-in-2m in
tests/imagination/pvr_vm_map.c):
CRITICAL: 33558528 bytes of shmem still held after close
- The parts still belong to the original object being split, but
pvr_vm_gpuva_remap() links them to ctx->gpuvm_bo, the new object's
vm_bo:
prev_va --obj--> BO_A BO_B <--obj-- vm_bo (ctx->gpuvm_bo)
\___________link___________/ (mismatch: BO_A != BO_B)
drm_gpuva_link() catches the mismatch:
WARNING: drivers/gpu/drm/drm_gpuvm.c:2108 at drm_gpuva_link+0x2ec/0x310
drm_WARN_ON(obj != vm_bo->obj)
Call trace:
drm_gpuva_link
pvr_vm_gpuva_remap
__drm_gpuvm_sm_map
pvr_vm_map
pvr_ioctl_vm_map
Link them to op->remap.unmap->va->vm_bo instead.
The locking of the GPUVA lists of the other objects touched by a split is
not addressed here; it is handled by switching the GPUVM to immediate
mode. |
| In the Linux kernel, the following vulnerability has been resolved:
flow_dissector: avoid u16 truncation of hlen in bpf_flow_dissect()
bpf_flow_dissect() sanitizes the offsets returned by the BPF program
with clamp_t(u16, ..., hlen).
If hlen is bigger than 65535, the upper bound is truncated before
the comparison. For instance, with hlen == 65536, both nhoff and
thoff are forced to zero, even if the program returned sane values.
This is the same class of bug as the one fixed in commit 99bda1ecbd56
("flow_dissector: avoid u16 truncation of skb->len when computing
thoff"). That fix does not cover the BPF path, because
__skb_flow_dissect() returns early when a BPF flow dissector
handles the packet.
struct bpf_flow_keys stores nhoff and thoff as u16, so cap hlen
to U16_MAX before clamping.
Found by sashiko while reviewing the commit above. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: free iov when btrfs_uring_read_extent() fails
After btrfs_uring_read_extent(), the caller always jumped to out_acct.
That skips kfree(data->iov), which is only correct for -EIOCBQUEUED
where the deferred path owns the iov. On failure, fall through to
out_free instead. |
| In the Linux kernel, the following vulnerability has been resolved:
statmount: read the parent of an unmounted mount under mount_lock
statmount_mnt_basic() reads the ids of the parent through m->mnt_parent
with namespace_sem held for reading. That's fine for a mount that is
in a namespace. Everything above it is pinned by that namespace.
STATMOUNT_BY_FD also accepts a file descriptor on a mount that has
been unmounted on purpose and that only the file descriptor keeps alive.
If that mount stayed attached to its parent when it was unmounted the
parent is unmounted as well and nothing pins it for the child.
The final mntput() unmounts the children under mount_lock alone and
frees the parent afterwards. Concurrently, statmount_mnt_basic() reads
m->mnt_parent twice while that can happen and can easily dereference a
mount that's already gone.
Read the parent of an unmounted mount under mount_lock. The parent
can't be put while it is held and both ids come from the same mount. A
mounted mount's parent is pinned by the namespace and a mount can't
leave its namespace while namespace_sem is held, so the common case
takes no global lock. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: validate userspace queue count against initialized firmware slot count
In panthor_drv.c:panthor_ioctl_group_create(),
the queue count is validated against the hardcoded maximum:
if (!args->queues.count || args->queues.count > MAX_CS_PER_CSG)
return -EINVAL;
However, if the firmware reports fewer slots than MAX_CS_PER_CSG,
panthor_fw_init_ifaces() will only initialize that smaller number of
stream interfaces.
If unprivileged userspace requests more queues than the firmware reported
(but no more than MAX_CS_PER_CSG), cs_slot_prog_locked() fetches an
uninitialized stream interface and may crash when dereferencing
cs_iface->input->ringbuf_base. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/fb-helper: defer setup when fbdev_probe() fails, not just on -EAGAIN
__drm_fb_helper_initial_config_and_unlock() calls
drm_client_modeset_probe() first, which already fills in each
mode_set->mode/num_connectors for every connected output, and only
afterwards calls drm_fb_helper_single_fb_probe() to create
fb_helper->fb and wire it into those mode_sets via
drm_setup_crtcs_fb().
If drm_fb_helper_single_fb_probe() fails with anything other than
-EAGAIN (e.g. dev->driver->fbdev_probe() itself fails), the function
bails out before drm_setup_crtcs_fb() runs and before setting
fb_helper->deferred_setup. The client is left with mode_sets that
have a mode and connectors but mode_set->fb == NULL, and nothing
marks this fb_helper as needing a retry.
__drm_fb_helper_restore_fbdev_mode_unlocked() only skips committing
when fb_helper->deferred_setup is set, so a later .restore() call
(drm_lastclose() on process exit, in this report) commits the stale
mode_set through drm_client_modeset_commit() ->
drm_client_modeset_commit_atomic() -> __drm_atomic_helper_set_config(),
which hits WARN_ON(!set->fb).
Mark fb_helper->deferred_setup on any drm_fb_helper_single_fb_probe()
failure, not just -EAGAIN, so restore keeps skipping the commit until
a later hotplug event successfully re-probes and re-populates
mode_set->fb. The real error code is still returned to the caller
unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: Don't cast tpacket_hdr.tp_len to int in tpacket_parse_header().
syzbot reported BUG() in sock_sendmsg_nosec(). [0]
The problem is that tpacket_parse_header() casts user-provided
tpacket_hdr.tp_len, which is u32, to int.
If the length is larger than INT_MAX, the following condition
in tpacket_parse_header() passes,
if (unlikely(tp_len > size_max))
and any negative value can be returned to the caller, up to
sock_sendmsg_nosec().
The repro set tpacket_hdr.tp_len to 0xfffffdef, which is cast
to -EIOCBQUEUED (-529), triggering BUG() in sock_sendmsg_nosec().
*(uint64_t*)0x200000000008 = 0xfffffdef;
...
syscall(__NR_write, /*fd=*/r[0], /*buf=*/0x200000000000ul, /*count=*/1ul);
Let's define the local tp_len as u32 in tpacket_parse_header().
[0]:
kernel BUG at net/socket.c:803!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 5628 Comm: syz-executor176 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/24/2026
RIP: 0010:sock_sendmsg_nosec+0x145/0x180 net/socket.c:803
Code: 06 67 48 0f b9 3a eb 95 e8 e8 3a 22 f8 48 89 df 4c 89 f6 4c 89 e2 4d 89 fb 2e e8 32 a5 5c 16 e9 51 ff ff ff e8 cc 3a 22 f8 90 <0f> 0b e8 c4 3a 22 f8 48 83 c3 18 48 89 d8 48 c1 e8 03 42 80 3c 28
RSP: 0018:ffffc90003aefb48 EFLAGS: 00010293
RAX: ffffffff89a578d4 RBX: ffff8880764c67c0 RCX: ffff88807fb23e80
RDX: 0000000000000000 RSI: 00000000fffffdef RDI: 00000000fffffdef
RBP: 00000000fffffdef R08: ffffc90003aef747 R09: 1ffff9200075dee8
R10: dffffc0000000000 R11: fffff5200075dee9 R12: 0000000000000001
R13: dffffc0000000000 R14: ffffc90003aefbc0 R15: ffffffff8aac4310
FS: 000055559101b400(0000) GS:ffff888124ce0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000000210 CR3: 0000000073dca000 CR4: 00000000003526f0
Call Trace:
<TASK>
__sock_sendmsg net/socket.c:815 [inline]
sock_write_iter+0x2de/0x3e0 net/socket.c:1266
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x612/0xba0 fs/read_write.c:687
ksys_write+0x150/0x270 fs/read_write.c:739
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x166/0x520 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f173130ecb9
Code: c0 79 93 eb d5 48 8d 7c 1d 00 eb 99 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 d8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd67e44248 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000200000000000 RCX: 00007f173130ecb9
RDX: 0000000000000001 RSI: 0000200000000000 RDI: 0000000000000003
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffd67e44388
R13: 0000000000000002 R14: 00002000000000c0 R15: 0000000000000002
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ch: Do not keep references to data transfer element devices
ch_readconfig() looks up the scsi_device of every data transfer element
whose SCSI id the changer reports in READ ELEMENT STATUS, and stores it in
ch->dt[]. scsi_device_lookup() takes a reference, and nothing ever drops
it: ch_destroy() frees the array with kfree(). ch->dt[] is read nowhere
else - it only supplies the vendor, model and revision printed in the same
loop.
Once such a drive is removed, its scsi_device can never be released. It
stays on the host's device list at its address, so a new device there is
refused by anything that walks the list - target_core_pscsi reports
"scsi_device_get() failed for H:C:T:L" - and the low-level driver's module
can no longer be unloaded. Only a reboot recovers.
It shows with any changer that reports its drives' ids; with the mhvtl
virtual library (IBM 3573-TL personality), each create and remove of a
library with four drives leaves four references behind, counted by the
module's use count in lsmod. With ch not bound the count is unchanged, and
with this patch applied it is unchanged too.
Drop the reference as soon as the name has been printed, and remove the now
unused dt[] array. That also removes the array leaked when ch_probe() fails
after ch_readconfig().
The same leak was reported with an RFC patch in 2022, which was not merged. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: of: fill in supply names in of_regulator_bulk_get_all()
of_regulator_bulk_get_all() returns an array it allocated itself, and
fills in only the consumer of each entry. Every other way of getting a
bulk array has the supply name set, because the caller provides it, and
the core expects it to be there: regulator_bulk_enable() prints it when
a supply fails to enable, so a caller that hands such an array to it
dereferences uninitialised memory on that path.
Copy each name into the array's own allocation, right behind the
entries, so that it shares the array's lifetime and callers still have
nothing extra to free. That also retires the fixed 64 byte stack buffer
the names were assembled in, which is_supply_name() never bounded the
copy against. |
| In the Linux kernel, the following vulnerability has been resolved:
net: team: stop reusing skb after queue override
A nonzero dev_queue_xmit() result does not return ownership of the skb.
When an override port's qdisc drops it, the queue override helper used to
try another port or the mode transmit op with the freed skb.
Return the handoff decision separately from transmit success. Select only
the first override port under RCU and stop after handing it the skb,
regardless of the lower transmit result. Keep the existing success and
drop accounting.
BUG: KASAN: slab-use-after-free in sk_skb_reason_drop
Write of size 4 by task poc/5040
sk_skb_reason_drop (net/core/skbuff.c:1240)
dev_kfree_skb_any_reason (net/core/dev.c:3470)
ab_transmit (drivers/net/team/team_mode_activebackup.c:49)
team_xmit (drivers/net/team/team_core.c:1849)
__dev_direct_xmit (net/core/dev.c:4934)
Freed by task 5040:
__tcf_kfree_skb_list (net/sched/sch_generic.c:43)
__dev_queue_xmit (net/core/dev.c:4831)
team_xmit (drivers/net/team/team_core.c:1846)
Kernel panic - not syncing: KASAN: panic_on_warn set ... |
| In the Linux kernel, the following vulnerability has been resolved:
net: xilinx: axienet: Free outstanding DMA buffers on dmaengine stop
In the dmaengine path the driver pre-submits RX buffers and holds
in-flight TX buffers whose SKBs are DMA-mapped by the driver and freed
only in the completion callbacks. On ndo_stop() dmaengine_terminate_sync()
aborts these descriptors without running their callbacks, and the driver
then frees only the ring shells, leaking every SKB still owned by the
engine and its DMA mapping on each ifdown. With 128 RX buffers pre-posted
per channel, the mapping leak can eventually exhaust a limited IOMMU
aperture.
Clear the slot's skb in the TX and RX callbacks so a non-NULL skb marks a
slot that still owns a live, DMA-mapped buffer, and on stop unmap and free
every such buffer.
axienet_dma_rx_cb() runs from the DMA tasklet and re-arms the RX ring on
each completion, so it can race axienet_stop(): a completion may submit a
fresh buffer after dmaengine_terminate_sync() has returned, leaving the
channel armed with a buffer the teardown then frees while the engine may
still write into it (dma_release_channel() does not stop it either). Add a
lock that axienet_dma_rx_cb() holds across the @stopping check and the
resubmit, and axienet_stop() holds to set @stopping before terminating.
Once @stopping is set no callback can arm a new buffer, and any armed just
before is aborted by the terminate, so teardown only frees buffers the
engine no longer owns. |
| In the Linux kernel, the following vulnerability has been resolved:
net: sparx5: free the matchall entry on destroy
sparx5_tc_matchall_replace() allocates a struct sparx5_mall_entry for
every offloaded matchall filter and adds it to sparx5->mall_entries.
sparx5_tc_matchall_destroy() removes the entry from the list, but never
frees it, so the entry of every deleted mirror and goto matchall filter
is leaked.
Free the entry after unlinking it.
The leak was discovered by an AI code review agent, and reproduced with
kmemleak on a lan969x EV board (EV23X71A) by repeatedly adding and
deleting matchall mirror and goto filters. With the fix, kmemleak no
longer reports the leak. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: tty_port: restore TTY_IO_ERROR on activation failure
Make sure to restore the TTY_IO_ERROR flag if activation fails to
prevent I/O attempts on a port that is gone or powered down.
This specifically avoids issues like kernel panic due to unclocked
accesses or NULL-pointer dereferences when accessing powered down or
deregistered ports when a TTY ioctl races with hangup and open.
Note that the flag is set again in tty_port_close() but not restoring it
on activation failure leaves a window where drivers fail to handle the
ioctl-hangup race. |
