| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down context entry
When tearing down a context entry, the current implementation zeros the
entire 128-bit entry using multiple 64-bit writes. This creates a window
where the hardware can fetch a "torn" entry — where some fields are
already zeroed while the 'Present' bit is still set — leading to
unpredictable behavior or spurious faults.
While x86 provides strong write ordering, the compiler may reorder writes
to the two 64-bit halves of the context entry. Even without compiler
reordering, the hardware fetch is not guaranteed to be atomic with
respect to multiple CPU writes.
Align with the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the context entry first to
signal the transition of ownership from hardware to software.
2. Use dma_wmb() to ensure the cleared bit is visible to the IOMMU.
3. Perform the required cache and context-cache invalidation to ensure
hardware no longer has cached references to the entry.
4. Fully zero out the entry only after the invalidation is complete.
Also, add a dma_wmb() to context_set_present() to ensure the entry
is fully initialized before the 'Present' bit becomes visible. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: do not keep dest_dst if dev is going down
There is race between the netdev notifier ip_vs_dst_event()
and the code that caches dst with dev that is going down.
As the FIB can be notified for the closed device after our
handler finishes, it is possible valid route to be returned
and cached resuling in a leaked dev reference until the dest
is not removed.
To prevent new dest_dst to be attached to dest just after the
handler dropped the old one, add a netif_running() check
to make sure the notifier handler is not currently running
for device that is closing. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation
Ulrich reports a regression with nfqueue:
If an application did not set the 'F_GSO' capability flag and a gso
packet with an unconfirmed nf_conn entry is received all packets are
now dropped instead of queued, because the check happens after
skb_gso_segment(). In that case, we did have exclusive ownership
of the skb and its associated conntrack entry. The elevated use
count is due to skb_clone happening via skb_gso_segment().
Move the check so that its peformed vs. the aggregated packet.
Then, annotate the individual segments except the first one so we
can do a 2nd check at reinject time.
For the normal case, where userspace does in-order reinjects, this avoids
packet drops: first reinjected segment continues traversal and confirms
entry, remaining segments observe the confirmed entry.
While at it, simplify nf_ct_drop_unconfirmed(): We only care about
unconfirmed entries with a refcnt > 1, there is no need to special-case
dying entries.
This only happens with UDP. With TCP, the only unconfirmed packet will
be the TCP SYN, those aren't aggregated by GRO.
Next patch adds a udpgro test case to cover this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Fix race in DMA ring dequeue
The HCI DMA dequeue path (hci_dma_dequeue_xfer()) may be invoked for
multiple transfers that timeout around the same time. However, the
function is not serialized and can race with itself.
When a timeout occurs, hci_dma_dequeue_xfer() stops the ring, processes
incomplete transfers, and then restarts the ring. If another timeout
triggers a parallel call into the same function, the two instances may
interfere with each other - stopping or restarting the ring at unexpected
times.
Add a mutex so that hci_dma_dequeue_xfer() is serialized with respect to
itself. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not ASSERT() when the fs flips RO inside btrfs_repair_io_failure()
[BUG]
There is a bug report that when btrfs hits ENOSPC error in a critical
path, btrfs flips RO (this part is expected, although the ENOSPC bug
still needs to be addressed).
The problem is after the RO flip, if there is a read repair pending, we
can hit the ASSERT() inside btrfs_repair_io_failure() like the following:
BTRFS info (device vdc): relocating block group 30408704 flags metadata|raid1
------------[ cut here ]------------
BTRFS: Transaction aborted (error -28)
WARNING: fs/btrfs/extent-tree.c:3235 at __btrfs_free_extent.isra.0+0x453/0xfd0, CPU#1: btrfs/383844
Modules linked in: kvm_intel kvm irqbypass
[...]
---[ end trace 0000000000000000 ]---
BTRFS info (device vdc state EA): 2 enospc errors during balance
BTRFS info (device vdc state EA): balance: ended with status: -30
BTRFS error (device vdc state EA): parent transid verify failed on logical 30556160 mirror 2 wanted 8 found 6
BTRFS error (device vdc state EA): bdev /dev/nvme0n1 errs: wr 0, rd 0, flush 0, corrupt 10, gen 0
[...]
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
------------[ cut here ]------------
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
kernel BUG at fs/btrfs/bio.c:938!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 868 Comm: kworker/u8:13 Tainted: G W N 6.19.0-rc6+ #4788 PREEMPT(full)
Tainted: [W]=WARN, [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Workqueue: btrfs-endio simple_end_io_work
RIP: 0010:btrfs_repair_io_failure.cold+0xb2/0x120
RSP: 0000:ffffc90001d2bcf0 EFLAGS: 00010246
RAX: 0000000000000051 RBX: 0000000000001000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8305cf42 RDI: 00000000ffffffff
RBP: 0000000000000002 R08: 00000000fffeffff R09: ffffffff837fa988
R10: ffffffff8327a9e0 R11: 6f69747265737361 R12: ffff88813018d310
R13: ffff888168b8a000 R14: ffffc90001d2bd90 R15: ffff88810a169000
FS: 0000000000000000(0000) GS:ffff8885e752c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
------------[ cut here ]------------
[CAUSE]
The cause of -ENOSPC error during the test case btrfs/124 is still
unknown, although it's known that we still have cases where metadata can
be over-committed but can not be fulfilled correctly, thus if we hit
such ENOSPC error inside a critical path, we have no choice but abort
the current transaction.
This will mark the fs read-only.
The problem is inside the btrfs_repair_io_failure() path that we require
the fs not to be mount read-only. This is normally fine, but if we are
doing a read-repair meanwhile the fs flips RO due to a critical error,
we can enter btrfs_repair_io_failure() with super block set to
read-only, thus triggering the above crash.
[FIX]
Just replace the ASSERT() with a proper return if the fs is already
read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: check truncate permission under inode lock
nfsd_setattr() checks whether a size update needs NFSD_MAY_TRUNC
before it takes inode_lock(). The comparison uses the file size sampled
by that unlocked read, but the actual ATTR_SIZE update is applied later
under inode_lock() by notify_change().
This leaves a TOCTOU window for append-only files. If a client sends a
SETATTR that does not shrink the file at the time of the unlocked
sample, a concurrent append can extend the file before nfsd_setattr()
takes inode_lock(). notify_change() then applies a real truncation
without the NFSD_MAY_TRUNC check that rejects IS_APPEND(inode). The VFS
truncate syscall paths perform their own append-only checks before
calling notify_change(), so NFSD must make this decision against the
locked size it is about to change.
Split the write-count acquisition from the truncation permission check.
Keep get_write_access() before the locked setattr work, then recheck
whether the requested size is below i_size_read(inode) after inode_lock()
has been acquired and before notify_change(ATTR_SIZE). This also avoids
the plain unlocked inode->i_size load. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix UAF in check_new_map() on session freed during unlock
check_new_map() iterates mdsc->sessions[] and for each active session
drops mdsc->mutex to perform per-session operations. The forced-close
path (rank removed from map) correctly takes a reference on s via
ceph_get_mds_session() before releasing mdsc->mutex, but three other
paths do not:
Path A (address changed): mutex_unlock → mutex_lock(&s->s_mutex)
Path B (reconnect): mutex_unlock → send_mds_reconnect(mdsc, s)
Path C (active transition): mutex_unlock → mutex_lock(&s->s_mutex)
Without the extra reference, another thread can acquire mdsc->mutex
during the unlock window, call __unregister_session() which drops the
last reference on s, and free it. The original thread then accesses
freed memory via s->s_mutex.
Fix by adding ceph_get_mds_session(s) before each mutex_unlock and
ceph_put_mds_session(s) after the corresponding mutex_lock, matching
the pattern already used in the forced-close path.
Race timeline (Path A):
Thread A (check_new_map) Thread B (another map update
holds mdsc->mutex or session teardown)
-------------------------- --------------------------
s = mdsc->sessions[i]
(refcount == 1, held only by
sessions[] array)
mutex_unlock(&mdsc->mutex)
---> acquires mdsc->mutex
__unregister_session(mdsc, s)
sessions[i] = NULL
ceph_put_mds_session(s)
refcount: 1 -> 0
kfree(s) <--- freed!
mutex_lock(&s->s_mutex)
UAF on freed s->s_mutex |
| In the Linux kernel, the following vulnerability has been resolved:
HID: sony: fix UAF of ghl_poke_timer / ghl_urb at driver unbind
For GHL (Guitar Hero Live) dongles, sony_probe() arms a periodic timer:
ghl_magic_poke() (the timer callback) submits sc->ghl_urb, and the URB
completion ghl_magic_poke_cb() re-arms the timer with mod_timer().
sony_remove() drained the timer with timer_delete_sync() and then freed
the URB with usb_free_urb():
timer_delete_sync(&sc->ghl_poke_timer);
usb_free_urb(sc->ghl_urb);
timer_delete_sync() does not block re-arming, and while the URB is in
flight the timer is not pending, so the sync delete is a no-op. A URB
completion that runs after the delete re-arms the timer, and usb_free_urb()
only drops a reference -- it does not kill an in-flight URB. sc is
allocated with devm_kzalloc() and freed once sony_remove() returns, so the
re-armed ghl_poke_timer (embedded in sc) then fires on freed memory, a
use-after-free from timer softirq. This is a disconnect/rmmod race.
Poison the URB first, then shut the timer down, before freeing the URB.
usb_poison_urb() kills any in-flight URB and permanently rejects further
submissions, so a poke timer that is still pending cannot re-submit the
URB from ghl_magic_poke() in the window before timer_shutdown_sync() runs.
usb_kill_urb() would not suffice: it only cancels the in-flight URB and
leaves it submittable once it returns, so the pending timer could
re-submit it and put a fresh URB in flight over the freed sc.
timer_shutdown_sync() then drains any last callback and blocks re-arming.
The probe error path is unaffected: it is only reached before the timer
is armed.
Reproduced under KASAN on next-20260710 via dummy_hcd + raw-gadget
emulation of the GHL PS4 dongle (VID 0x1430 / PID 0x07bb): hid-sony binds
and arms the poke timer, the poke URB is held in flight, the driver is
unbound (freeing sc), then the URB is released. The completion re-arms the
timer on the freed sc, and the re-armed timer fires ~8 s later:
BUG: KASAN: slab-use-after-free in ghl_magic_poke+0x98/0xb0
Read of size 8 at addr ffff88810b02fd50 by task swapper/0/0
ghl_magic_poke+0x98/0xb0
call_timer_fn+0x35/0x2b0
__run_timers+0x69c/0x9a0
run_timer_softirq+0x173/0x2a0
Allocated by task 169: sony_probe
Freed by task 338: devres_release_group <- hid_device_remove (sony_remove)
Found by 0sec (https://0sec.ai) using automated source analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/core: Make core-sched flips wait for in-flight selections
Core scheduling's pick_next_task() operates on all sibling rqs under one
acquisition of the shared core-wide lock. A ->pick_task() that releases the
rq lock leaves every sibling __lock momentarily free, letting
__sched_core_flip(false) complete mid-selection and rebind rq_lockp() under
it. The selection resumes on the split locks, touching sibling state it no
longer protects, and __schedule() finally releases a lock that was never
taken while leaking the one that was.
Count in-flight core-wide selections in the leader's rq->core_pick_in_flight
and make __sched_core_flip() wait for the count to drain. The count only
changes under the shared lock, which the flip holds while sampling, so no
other ordering is needed. The wait can repeat while selections overlap, but
the flip backs off between samples and flips are rare cookie-lifetime
events.
sched_core_cpu_deactivate() moves the count to the new leader - a stale copy
left behind would bias it forever if that CPU later returns as its own
leader. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: charger-manager: register regulators before exposing sysfs
charger_manager_remove() and the err_reg_extcon probe error path free each
charger regulator with regulator_put() before tearing down the power_supply
sysfs entries (power_supply_unregister()). charger_manager_remove() also
calls try_charger_enable(cm, false) after the regulator_put() loop. A
concurrent write to a charger's externally_control sysfs attribute that
lands between regulator_put() and power_supply_unregister() can run
charger_externally_control_store() and call try_charger_enable(), which,
when charging is enabled, dereferences the already-freed consumer handle.
When charging is enabled, try_charger_enable(cm, false) in .remove() also
dereferences the freed handles directly. Both leave use-after-free windows.
Symmetrically, probe registers the sysfs entries (power_supply_register)
before acquiring the regulators (regulator_get, inside
charger_manager_register_extcon), so userspace can reach externally_control
before the regulators are available.
Split charger_manager_register_extcon() on the sync/async boundary:
charger_manager_get_regulators() (regulator_get only, no async producer)
now runs before power_supply_register() so sysfs is not live before
regulators are available, and charger_manager_register_extcon() keeps only
the extcon notifier/work setup, still after power_supply_register() so a
power_supply_register() failure cannot reach extcon setup. This keeps the
sysfs setup/teardown ordering symmetric without introducing an asynchronous
producer on the earlier probe-error path.
Move power_supply_unregister() and try_charger_enable(cm, false) ahead of
the regulator_put() loop on both teardown paths, and adjust err_reg_extcon
(power_supply_unregister() then fall through err_regulator for
regulator_put(); get_regulators self-rolls back on its own failure).
This does not address the separate extcon-notifier-driven deref of the same
handles, which needs its own synchronization design.
Found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: lp8788-charger: fix use-after-free on remove
lp8788_charger_remove() flushes charger_work before unregistering the
IRQs. An IRQ thread can queue charger_work after flush_work() has
returned. The work can then run after devres frees pchg and dereference
it in lp8788_charger_event().
Unregister the IRQs first. free_irq() waits for any running threaded
handler, so no handler can queue more work afterwards. Then use
cancel_work_sync() to cancel pending work or wait for running work to
finish.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ravb: serialize PTP clock teardown
ravb_ptp_interrupt() can race with ravb_ptp_stop() and pass the clock to
ptp_clock_event() while ptp_clock_unregister() is freeing it. This can
lead to a use-after-free.
Use READ_ONCE() and WRITE_ONCE() for lockless access to the clock pointer.
Atomically detach it with xchg() before disabling PTP interrupts, then
synchronize all IRQs which can invoke ravb_ptp_interrupt() before
unregistering the detached clock.
A handler which read the old pointer completes before the clock is
unregistered, while later handlers read NULL and skip the event. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: stop killed, freed and out_of_sync sharing a byte
The three connection state flags are single-bit bitfields, so they occupy
one byte of struct smc_connection and every store to one is a
read-modify-write of the other two:
u8 killed : 1;
u8 freed : 1;
u8 out_of_sync : 1;
They are not written under a common lock. smc_cdc_msg_validate() sets
out_of_sync from the receive tasklet, while smc_conn_kill() sets killed
from process context under lock_sock(), and the receive path does not defer
to the backlog when the socket is owned -- smc_cdc_msg_recv() takes only
bh_lock_sock().
Give each flag its own byte so a store no longer touches its neighbours.
All readers test them as booleans and are unchanged. struct smc_connection
grows by two bytes. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: defer eventfd signaling when queued from a wakeup handler
io_req_local_work_add() signals the CQ ring eventfd inline when it is the
one to push the first entry onto ->work_list. For DEFER_TASKRUN rings that
add is frequently done from a waitqueue wakeup handler, where an
arbitrary waitqueue lock is held.
eventfd_signal_mask() only refuses to recurse when current->in_eventfd
is set, but that bit is set by eventfd_signal_mask() itself. If the wake
chain starts somewhere else, signal goes out inline and can feed back
into epoll.
Add IOU_F_TWQ_IN_WAKE, set it on the task_work add done from the three
waitqueue callbacks, and use it to force io_eventfd_signal() down the
existing call_rcu_hurry() deferral instead of signaling inline. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: clamp route advmss to TCP_MIN_MSS
tcp_select_initial_window() assumes that callers never pass an MSS
smaller than 1, but route-derived advmss values can violate that
assumption.
A too-small explicit RTAX_ADVMSS is one way to get there, but it is not
the only one. The same divide-by-zero can also be reached through the
"default advmss" path when RTAX_ADVMSS is left at 0 and the effective
advmss is later driven down by route MTU and min_adv_mss.
Introduce a tcp_dst_advmss() helper that clamps route advmss to
TCP_MIN_MSS before TCP consumes it, and use it in the TCP paths that
derive advmss from dst metrics. This keeps the effective MSS from
dropping to zero before tcp_select_initial_window() rounds the receive
window. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: hisi_sas: Add slave_destroy interface for v3 hw
WARNING is triggered when executing link reset of remote PHY and rmmod
SAS driver simultaneously. Following is the WARNING log:
WARNING: CPU: 61 PID: 21818 at drivers/base/core.c:1347 __device_links_no_driver+0xb4/0xc0
Call trace:
__device_links_no_driver+0xb4/0xc0
device_links_driver_cleanup+0xb0/0xfc
__device_release_driver+0x198/0x23c
device_release_driver+0x38/0x50
bus_remove_device+0x130/0x140
device_del+0x184/0x434
__scsi_remove_device+0x118/0x150
scsi_remove_target+0x1bc/0x240
sas_rphy_remove+0x90/0x94
sas_rphy_delete+0x24/0x3c
sas_destruct_devices+0x64/0xa0 [libsas]
sas_revalidate_domain+0xe4/0x150 [libsas]
process_one_work+0x1e0/0x46c
worker_thread+0x15c/0x464
kthread+0x160/0x170
ret_from_fork+0x10/0x20
---[ end trace 71e059eb58f85d4a ]---
During SAS phy up, link->status is set to DL_STATE_AVAILABLE in
device_links_driver_bound, then this setting influences
__device_links_no_driver() before driver rmmod and caused WARNING.
Add the slave_destroy interface to make sure link is removed after flush
workque. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: synproxy: fix unaligned memory access in timestamp adjustment
Use get_unaligned_be32() and put_unaligned_be32() to safely read and
write the timestamp fields. This prevents performance degradation due to
unaligned memory access or even a crash on strict alignment
architectures.
This follows the implementation of timestamp parsing in the networking
stack at tcp_parse_options() and synproxy_parse_options(). |
| In the Linux kernel, the following vulnerability has been resolved:
9p/xen: protect xen_9pfs_front_free against concurrent calls
The xenwatch thread can race with other back-end change notifications
and call xen_9pfs_front_free() twice, hitting the observed general
protection fault due to a double-free. Guard the teardown path so only
one caller can release the front-end state at a time, preventing the
crash.
This is a fix for the following double-free:
[ 27.052347] Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[ 27.052357] CPU: 0 UID: 0 PID: 32 Comm: xenwatch Not tainted 6.18.0-02087-g51ab33fc0a8b-dirty #60 PREEMPT(none)
[ 27.052363] RIP: e030:xen_9pfs_front_free+0x1d/0x150
[ 27.052368] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 41 55 41 54 55 48 89 fd 48 c7 c7 48 d0 92 85 53 e8 cb cb 05 00 48 8b 45 08 48 8b 55 00 <48> 3b 28 0f 85 f9 28 35 fe 48 3b 6a 08 0f 85 ef 28 35 fe 48 89 42
[ 27.052377] RSP: e02b:ffffc9004016fdd0 EFLAGS: 00010246
[ 27.052381] RAX: 6b6b6b6b6b6b6b6b RBX: ffff88800d66e400 RCX: 0000000000000000
[ 27.052385] RDX: 6b6b6b6b6b6b6b6b RSI: 0000000000000000 RDI: 0000000000000000
[ 27.052389] RBP: ffff88800a887040 R08: 0000000000000000 R09: 0000000000000000
[ 27.052393] R10: 0000000000000000 R11: 0000000000000000 R12: ffff888009e46b68
[ 27.052397] R13: 0000000000000200 R14: 0000000000000000 R15: ffff88800a887040
[ 27.052404] FS: 0000000000000000(0000) GS:ffff88808ca57000(0000) knlGS:0000000000000000
[ 27.052408] CS: e030 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 27.052412] CR2: 00007f9714004360 CR3: 0000000004834000 CR4: 0000000000050660
[ 27.052418] Call Trace:
[ 27.052420] <TASK>
[ 27.052422] xen_9pfs_front_changed+0x5d5/0x720
[ 27.052426] ? xenbus_otherend_changed+0x72/0x140
[ 27.052430] ? __pfx_xenwatch_thread+0x10/0x10
[ 27.052434] xenwatch_thread+0x94/0x1c0
[ 27.052438] ? __pfx_autoremove_wake_function+0x10/0x10
[ 27.052442] kthread+0xf8/0x240
[ 27.052445] ? __pfx_kthread+0x10/0x10
[ 27.052449] ? __pfx_kthread+0x10/0x10
[ 27.052452] ret_from_fork+0x16b/0x1a0
[ 27.052456] ? __pfx_kthread+0x10/0x10
[ 27.052459] ret_from_fork_asm+0x1a/0x30
[ 27.052463] </TASK>
[ 27.052465] Modules linked in:
[ 27.052471] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430 |
