| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: preserve hidden-group beacon IE ownership
A hidden-group probe-response entry borrows its beacon IEs from the
group's beacon entry. cfg80211_update_assoc_bss_entry() can pass such
an entry to cfg80211_update_known_bss() when merging scan entries
after a channel switch.
Copying the borrowed beacon_ies into the associated entry gives the
same allocation two owners. Releasing the group's beacon entry can
then leave the associated entry pointing to freed IEs, which are
freed again when that entry is released.
Skip beacon IE replacement when the source entry belongs to a hidden
group. Preserve probe-response processing, the subsequent metadata
updates, and the existing rejection path for conflicting hidden
beacon updates. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: filter some flags received in the backup server
While the IPVS SYNC protocol is not secure by design
we can still protect the backup server from messages that
can wreak havoc.
This commit addresses problems from received connection flags
or their combinations. We now drop messages as follows:
1. the NO_CPORT+TEMPLATE combination allows lookups for normal
connections to hit template which can break in many ways.
While the master does not sync connections with NO_CPORT flag,
i.e. before they are established, we still accept NO_CPORT
without TEMPLATE.
2. ONE_PACKET: it is not sent by master, so we do not
expect it in backup. Before now it was ignored by
IP_VS_CONN_F_BACKUP_MASK for protocol v1 while protocol
v0 created connections that are not hashed and dropped
immediately. Better to apply the IP_VS_CONN_F_BACKUP_MASK
also to the flags from v0 messages for consistency with v1. |
| In the Linux kernel, the following vulnerability has been resolved:
net: cap skb->queue_mapping when the tx queue is picked
skbedit can set skb->queue_mapping and raise the per-CPU skip_txqueue
flag so __dev_queue_xmit() honours the mapping. __dev_queue_xmit()
cleared the flag before sch_handle_egress() and only read it afterwards,
so the flag was not confined to the xmit that set it: a nested xmit
(mirred redirect or mirror, or a drop after skbedit) could set the flag
and the outer xmit would consume it for an skb that never went through
skbedit.
A forwarded packet still carries the ingress NIC's rx_queue + 1 in
skb->queue_mapping, so the outer device then indexes its tx queue state
with that stale value. Taprio's child array q->qdiscs[] is sized to the
device's queue count, so taprio_enqueue() indexes past its allocation
and dereferences the result as a struct Qdisc *.
We (ab)use the skb->nf_skip_egress which means "skip netfilter egress
for this packet" to tag to "am I in tc egress?". Despite the overload
I dont see it as a conflict since the marker is set only around the
single sch_handle_egress() call and ingress path is guarded by
tc_at_ingress.
I will send a followup(net-next) patch once this hits net-next to
rename the skb->nf_skip_egress bit/flag to skb->skip_egress
Arm the flag only from the egress classifier that can use it: raise
skip_txqueue from tcf_skbedit_act() only when it runs inside
sch_handle_egress(), thanks to skb->nf_skip_egress. An egress qdisc
classifier runs in q->enqueue(), after the tx queue has been picked,
so a mapping it sets cannot affect the current packet; arming the flag
there only pollutes it for a later xmit. Then own the flag for the xmit
frame the egress hook runs in: save the incoming value and clear it just
before sch_handle_egress(), and restore it after the hook - on the
consumed (drop) path, or, in the same call that reads it, on the
surviving path. The save and the restores stay inside the
egress_needed_key static branch, so a packet pays for them only when
egress hooks are active (2f1e85b1aee4).
Store the value netdev_cap_txqueue() selected back into skb->queue_mapping
in netdev_tx_queue_mapping(), as netdev_core_pick_tx() already does, so
the skip_txqueue path never hands a later reader on the xmit path a
mapping the device cannot serve. A store made still later in the same
frame, by a tc BPF program attached to a transmit qdisc, is outside this
path and is not re-capped; a separate followup will resolve that path.
netdev_xmit_skip_txqueue() returns the previous flag value so the
save-and-clear is one call, and a no-op stub is provided when
CONFIG_NET_EGRESS is disabled. skb->nf_skip_egress is compiled under
CONFIG_NET_EGRESS rather than CONFIG_NETFILTER_SKIP_EGRESS, so
skb_at_tc_egress() is valid whenever the egress path is built.
A local user in a network namespace can redirect a packet from a device
with more TX queues to one with fewer after setting a mapping valid only
on the larger device. That reaches these reads and, under KASAN, faults
with "slab-out-of-bounds in taprio_enqueue".
Conditions to recreate the bug: the report's own trigger is a local user
with CAP_NET_ADMIN in a network namespace, so no eBPF program is needed.
With CONFIG_NET_SCH_TAPRIO=y, CONFIG_NET_ACT_SKBEDIT=y,
CONFIG_NET_ACT_MIRRED=y, CONFIG_NET_CLS_MATCHALL=y,
CONFIG_NET_SCH_PRIO=y and KASAN enabled, create qa (3 queues), qb
(2 queues) and qc (1 queue) as dummy devices; put a taprio root on qb
(num_tc 1, queues 2@0) and clsact on all three; then add an egress
matchall filter on every device. On qa: "action skbedit queue_mapping 2
pipe action mirred egress redirect dev qb". On qb: "action mirred egress
mirror dev qc". On qc: "action skbedit queue_mapping 0 pipe". Send one
packet out qa. qc's skbedit sets the flag while qb's outer xmit is in
flight; without the fix qb consumes it and reads its two-entry taprio
child array with the forwarded packet's stale mapping. A qc whose
skb
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: drop oversized fragments to avoid extra_len overflow
In ieee80211_rx_h_defragment(), fragment payloads are accumulated into
entry->extra_len as subsequent fragments arrive:
entry->extra_len += rx->skb->len;
When the final fragment arrives, the head fragment is dequeued, and
pskb_expand_head() is called with entry->extra_len to ensure sufficient
tailroom for all queued fragments before copying:
if (skb_tailroom(rx->skb) < entry->extra_len) {
if (unlikely(pskb_expand_head(rx->skb, 0, entry->extra_len,
GFP_ATOMIC))) {
...
}
}
while ((skb = __skb_dequeue(&entry->skb_list))) {
skb_put_data(rx->skb, skb->data, skb->len);
dev_kfree_skb(skb);
}
In commit 69f132236827 ("mac80211: shrink struct
ieee80211_fragment_entry"), entry->extra_len was narrowed from unsigned
int to u16 in order to reduce structure memory footprint.
However, an IEEE 802.11 frame sequence can contain up to 16 fragments
(frag numbers 0..15). If a sequence of large fragments arrives (e.g. from
a malicious peer or rogue AP), the sum of fragment lengths can exceed
65535 bytes (for example, 15 fragments of 4400 bytes total 66000 bytes).
Because extra_len is a u16, this addition overflows and wraps around
modulo 65536 (e.g. 66000 wraps to 464).
Consequently, pskb_expand_head() allocates only the truncated amount of
tailroom (or is skipped entirely if the head fragment already has >= 464
bytes of tailroom). When skb_put_data() subsequently iterates through the
queued skb list, it appends the full payload into the undersized buffer,
causing skb_put() to trigger skb_over_panic() and crash the kernel in
softirq context.
A legitimate MSDU in IEEE 802.11 is at most 2304 bytes (or up to 7935/11454
bytes for A-MSDU, which is not fragmented), well below U16_MAX.
Fix this without increasing the size of struct ieee80211_fragment_entry by
checking whether adding the incoming fragment length would exceed U16_MAX.
If so, purge the queued fragments and drop the frame.
[assign a separate drop reason] |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kionix-kx022a: Fix array boundary check
The driver performs a sanity check for an array size, when converting a
register value to an array index. The check incorrectly accepts the
sizeof(array) as a last index, when last valid index should be
sizeof(array) - 1.
Fix the check by bailing out when index >= sizeof(array). |
| A flaw was found in device-mapper-multipath. A local user can trigger an out-of-bounds read by sending a command with a format string ending in a trailing percent character to the multipath daemon. This issue can allow the user to expose unintended daemon memory, leading to information disclosure, or cause the daemon to crash, resulting in a Denial of Service (DoS). |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: tps6594-regulator: Fix n_linear_ranges for TPS65224 BUCK2-4
The TPS65224 BUCK2, BUCK3 and BUCK4 descriptors pass 4 as
n_linear_ranges, but tps65224_bucks_2_3_4_ranges[] only has two
entries, covering selectors 0x00-0x45.
The linear range helpers loop over n_linear_ranges entries, so any
lookup of a selector above 0x45 reads past the end of the array and
treats whatever follows it as two more ranges. This happens on the
normal registration path when the core checks the voltage constraints
against every selector. TPS652G1 uses the same descriptors and is
affected too.
Use ARRAY_SIZE() so the count always matches the table. |
| In the Linux kernel, the following vulnerability has been resolved:
kprobes: Skip disarmed probes when checking optkprobe overlap
On x86, an optkprobe at A replaces five bytes with a jump. If a disabled
probe B is at A+2, get_optimized_kprobe() stops at B when arming a new
probe C at A+4. It leaves A optimized:
A A+1 A+2 A+3 A+4
A's jump | e9 | d0 | d1 | d2 | d3 |
after C | e9 | d0 | d1 | d2 | cc |
The INT3 for C overwrites the last byte of A's jump displacement, so
execution can jump to the wrong address. B can have prepared optinsns
while disarmed, but has no jump to unoptimize.
Continue past disarmed and unprepared probes to find the active optimized
probe before arming a probe in its jump. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Copy BASE if service data matches EIR_BAA_SERVICE_UUID
Copy the content of a Periodic Advertisement Report to BASE only if
the service UUID is Basic Audio Announcement Service UUID. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix CPU hotplug hang when a dying CPU's tasks sit in the BPF scheduler
A CPU going down has to empty its own rq. Its hotplug thread waits in
sched_cpu_wait_empty() until nothing else is left, and the only thing that
wakes it is balance_push(), which runs from __schedule() on the dying CPU
and pushes off the migratable tasks the CPU picks.
sched_ext breaks this. A task sitting on a user DSQ or held by the BPF
scheduler is still counted on its rq, but an inactive CPU no longer calls
ops.dispatch() and can't pull the task back. The dying CPU goes idle with
the task still counted, and one of two things happens:
- Another CPU consumes the task. The rq empties without a __schedule() on
the dying CPU, so the hotplug thread is never woken and cpu_down() hangs
holding cpu_hotplug_lock.
- The task is affine only to the dying CPU. Nothing can move it, and the
offline stalls until the watchdog ejects the BPF scheduler.
When the rq goes offline, re-enqueue every task on it that isn't already on
the local DSQ. An enqueue on an offline rq lands on the local DSQ, so the
dying CPU itself picks the tasks and balance_push() pushes them off, the
same as for the other sched classes. From then on no sched_ext path on
another CPU can pull a task off the rq.
ops.dispatch() currently stops as soon as the CPU goes inactive, and CPU
hotplug then waits for an RCU grace period before taking the rq offline. A
BPF-held task affine only to the dying CPU and preempted inside an RCU
read-side critical section would block that grace period, and the rq would
never go offline. Test SCX_RQ_ONLINE directly so that ops.dispatch() keeps
running until the rq goes offline. Only the dying CPU's own hotplug thread
clears the flag during teardown, and task_can_run_on_remote_rq() still keeps
other rqs' tasks off the CPU. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-crypt: reject the lmk IV mode with AEAD ciphers
A "capi:" table line that pairs an AEAD cipher with the lmk IV mode,
for example "capi:gcm(aes)-lmk" with the integrity:28:aead option,
causes an oops when it is loaded. lmk sets tfms_count to 64, but
crypt_alloc_tfms_aead only allocates one transform, so crypt_setkey
reads past the end of the tfms_aead array and calls crypto_aead_setkey
on the values it finds there.
lmk exists for compatibility with Loop-AES, which uses CBC, so refuse
it with an AEAD cipher rather than allocate 64 AEAD transforms. The
check cannot go in crypt_iv_lmk_ctr with the other lmk checks, because
the IV constructor runs after crypt_set_key.
Note that this is not a security bug because the memory corruption can
only be triggered by root. |
| Memory corruption vulnerabilities in the affected interface of AOS-10 could lead to remote code execution by an unauthenticated adjacent attacker. Successful exploitation could allow an attacker to execute arbitrary code as a privileged user on the underlying operating system. |
| An unauthenticated buffer overflow vulnerability exists in the PAPI protocol of AOS-8. Successful exploitation could allow an unauthenticated remote attacker to disrupt the availability of the affected service on the controller, with a limited impact to its integrity. |
| The Goobi viewer is a web application that allows digitised material to be displayed in a web browser. From version 23.03 to before version 26.05, SolrTools.cleanUpQuery() strips Solr local-parameter syntax ({!...}) from user-supplied query strings before they reach Solr. Its regex can be bypassed by wrapping the local parameter in a second pair of curly braces ({{!...}}): the outer braces are stripped, the inner {!...} survives intact, and a valid Solr local parameter is forwarded. The flaw is in the shared sanitizer, so it affects any endpoint that routes user input through cleanUpQuery. The double-brace bypass applies from v23.10 (the greedy \{(.+)\} regex); a related bare-!join rewrap path is present. This issue has been patched in version 26.05. |
| An incomplete list of disallowed inputs in the Python code validator of the run_script tool in AWS MCP Server might allow an authenticated remote user to execute arbitrary code within their own isolated session environment via a crafted script.
AWS fixed this issue service-side. No customer action is required. |
| Zephyr's OpenThread integration defined CONFIG_OPENTHREAD_JOINER_PSKD with default "J01NME" in modules/openthread/Kconfig.thread (previously subsys/net/l2/openthread/Kconfig, then subsys/net/l2/openthread/Kconfig.thread). J01NME is the example Joining Device Credential used throughout the public OpenThread and Thread commissioning documentation, including Zephyr's own samples/net/sockets/echo_client/README.rst, so it is not a secret. A firmware image built with CONFIG_OPENTHREAD_JOINER_AUTOSTART=y that never overrode the PSKd therefore shipped with a publicly known joining credential compiled in, with no build-time or run-time warning.
The PSKd is the only value that authenticates Thread commissioning: joiner and commissioner run a DTLS-PSK handshake keyed on it, after which the commissioner supplies the full operational dataset. In ot_configure_instance() (modules/openthread/openthread.c), a device with no stored dataset calls otJoinerStart() with the configured PSKd, and ot_joiner_start_handler() calls otThreadSetEnabled() on success. An unauthenticated attacker within 802.15.4 radio range of an uncommissioned device (factory-fresh, after a factory reset, or after a settings erase) can run any stock Thread commissioner registered with J01NME, complete the handshake, and hand the device an attacker-controlled operational dataset.
The device then joins and enables Thread on the attacker's mesh. The attacker becomes its router, seeing, dropping, injecting and spoofing all of the device's IPv6 traffic and impersonating the peers the application expects, while the device is cut off from the network it was meant to join and stays mis-provisioned until it is reset. Only application-layer security with independently provisioned credentials survives. Exposure is limited to builds that enable joiner autostart and leave the PSKd unset; the option is not enabled by default and no in-tree sample uses the vulnerable combination.
The fix removes the default from CONFIG_OPENTHREAD_JOINER_PSKD and adds a BUILD_ASSERT() in modules/openthread/openthread.c, active only under CONFIG_OPENTHREAD_JOINER_AUTOSTART, that fails the build unless a 6-to-32-character PSKd is configured. Products should provision a per-device PSKd from factory data and call otJoinerStart() from the application rather than relying on a credential compiled identically into every unit. |
| odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. Prior to version 25.12, odhcpd's DHCPv6 IA response handler writes past the end of a fixed 512-byte stack buffer (pdbuf) when a single DHCPv6 REQUEST carries enough IA options to nearly exhaust the reply space. Two independent overflow sites exist in the same call chain, both reachable from the network via a single unauthenticated UDP packet. odhcpd runs as root on OpenWrt; embedded targets often lack stack canaries and ASLR, making code execution realistic. This issue has been patched in version 25.12. |
| odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. From version 17.01.0 to before version 25.12.3, odhcpd's DHCPv6 IA parser accepts an IA_NA or IA_PD option whose body is shorter than struct dhcpv6_ia_hdr, casts the option header to that full structure, and reads ia->iaid before proving that the IA body contains the IAID field. If an unauthenticated network-adjacent client places a zero-length or otherwise short IA option at the end of odhcpd's 8192-byte receive stack buffer, the IAID read crosses from data_buf into adjacent stack memory. The disclosed bytes are then reflected in the DHCPv6 reply IAID; prior ARM validation showed data_buf[8192:8196] disclosing the saved stack canary, and wider stack scans can leak ASLR-useful stack/process contents. This issue has been patched in version 25.12.3. |
| odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. In versions 25.12 and prior, odhcpd's DHCPv6 self-loop detection at dhcpv6.c:720 uses a network-byte-order DUID length value directly as the memcmp() size parameter. On little-endian hosts, this causes memcmp() to read far beyond the stack buffer — a single unauthenticated DHCPv6 packet triggers a 2560-byte overread from a 128-byte buffer. At time of publication, there are no publicly available patches. |
| A hostname canonicalization vulnerability in the email HTML sanitizers of Zimbra Collaboration Suite (ZCS) allows an unauthenticated sender to bypass the restriction on forms that target the Zimbra host. DefangFilter and the OWASP ActionAttributePolicy compare the form-action hostname with the request hostname before browser URL canonicalization. A percent-encoded hostname can therefore survive sanitization while the browser submits the form to the normal Zimbra origin with the recipient's authentication cookie. This permits authenticated form requests from a crafted email after the recipient opens it in Classic and submits the form. The issue is present in ZCS 10.1.16 and 10.1.21. It does not bypass an endpoint's CSRF-token checks; a state-changing attack additionally requires an endpoint that accepts the resulting request without that protection. |
